Summer Starts Here - Save up to 70%
# 1
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
The system is not what was advertised, it's better, at least for me. Everything arrived on a pallet in excellent condition, except for the advertised remote. I contacted etrailer and they put a replacement on order which I received a few days later. In the meantime, I tried to place the controller in the mode to sync the remote and see if the remote I had with my RV would sync, but I could not get the controller in that mode to accept a remote. Upon reading the controller label, I noticed it said BT and had a passcode on the side of it, so I downloaded the app and it connected to my phone. It seems the LCI Linc remote is obsolete for my Ground Control 3.0 and it is now using the phone app. Everything seems to work as expected; I'm excited to try everything out this weekend on our first outing. I was able to push a fiberglass push stick from the front basement to where the rear jacks are located without dropping the underbelly and pull all the required cables to the rear of the camper and utilize existing frame holes to bring the connectors out to the rear jacks. I think this will be a nice upgrade to our fifth wheel after our factory landing gear failed.
shipped in a timely manner. Easy install wit good instructions. I did have one question about the location of the rear lifts and called the company and we had an answer instantly. Wiring was very easy with good instructions. The system worked on the first try and have had no issues so far. Great system. I was looking at newer campers with auto leveling and about 40 to $50,ooo if I traded my paid for camper in. The cost saved me a lot of money and works as it should and saves my back and a lot of set up time. would and have recommended to others. Thanks.
# 2
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set
Let me say this to start, this system is AWESOME!! If you do not have a leveling system on your camper, this one works very , very well. I will say, the install and the learning curve takes time and is not too hard, but it's not super easy either. Once I got the system in place, and understood how to use it, the rest was a piece of cake. Take your time on the install and get help. The parts are robust and heavy, so two people make it much easier. Have sharp drill bits to drill the attachment holes. Wiring is super simple, but take your time and make sure you get all the connections good and tight and secured well with zip ties. The system requires a good strong battery, so make sure your battery is in great shape and you will not have any issues. Get the Lippert app also, it is very helpful. I love it now, when I pull my 2006 Keystone Raptor 5th wheel toy hauler into a campsite, I hit a couple buttons and the longest it has taken to level my unit is 2 minutes and 30 seconds. I love it! It puts the camper at the same level every single time, which is awesome. No guessing, no driving up and down on blocks, just push a button and walk away until the camper is perfect. Would I do this over again you ask? Absolutely. Awesome system!
After the initial installation there was a little confusion about setup I have been very happy with the way it works really simple push one button hit auto levels it's still working well thanks
# 3
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
Wowzers, what having two motors working to lift my 5th wheel toy hauler. Lifts it with no problem. Fast, makes hooking up and unhooking a breeze. No more struggling like it would with the stock single motor setup. Wish I would have done this years ago, not when one of my legs gears stripped on the first day of a 5 day NASCAR weekend. Good thing I had a 6 ton bottle jack, several wood blocks, got it off my truck, enjoyed the weekend and ordered these first thing when I got home. Install wasn't bad, if you work on things, should be no problem. Mild modification of my trailer hangers and flooring in the storage where the legs are, but nothing major. Hooked up to my truck to take the weight off instead of using jack stands. About 6 hours total, took my time to do it right.
I bought this to replace the under powered OEM landing gear on my 2018 39' toy hauler 5th wheel. I received great service from etrailer staff. First time for me to remove and replace landing gear so after 1 or 2 youtube videos I was able to get it done with a little grinding and drilling (and cursing). I've been using the new landing gear for a year now and here are my thoughts: PROS: Ability to adjust the 2 sides independently. Makes leveling much easier. Quality hardware and stronger motors. CONS: The toggle switches that come with it are very stiff and a bit awkward to use. The pin at the bottom of each leg is not attached. You have to pull it out, then line it up with the hole to replace it. All others I've seen have a spring loaded guided pin. The legs don't go up or down any faster than the OEM. Although that was never claimed, I was hoping they would. Overall I am happy with the product. I will say, if I had to do it again I would strongly consider going with the competitor's product for the better controls and spring loaded pins.
# 4
Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs
One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!
We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!
# 5
HappiJac Electric Truck Camper Jack System - 36-1/2" Lift - 11,200 lbs
You guys went above and beyond my expectations with my shipment . After having a hiccup in shipping you shipped out the next box super quick and I was super happy with your service. Thanks etrailer
Delivered on time, and time will tell how they operate compared to the 4500.
# 6
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
# 7
Ultra-Fab Electric A-Frame Jack w/ 7-Way Plug - 18" Lift - 3,500 lbs
I've had this power jack for about a year and it works flawlessly, it beats hand cranking. And not to mention the great service from etrailer their the best in the business.
Bought Pro Series Weight Dist Hitch, Jameson C was very helpful picking the right one out , ordered it on Friday and it arrived on Wednesday a day earlier than expected. Placed a second order for an electric jack and misc. parts. Extremely happy with their service. I don't review stuff but these guys deserve one.
# 8
Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift
Good thing stabilizer was easy to install because there were no directions included. Item was delivered quickly. I received item within a week.
Box is damaged and tape all over with clear tape holding box closed and first thought is missing parts and paper work and instructions to install ! Pictures taken and open up box finding all parts inside except for the paper work instructions to install, also the rubber cover for the water poof motor is damaged also!
# 9
HappiJac Electric Truck Camper Jack System - 34-1/2" Lift - 8,800 lbs
Fantastic service. Got my product day before they said it was going to be delivered.
a great t way to raise and lower camper. Only takes minutes and you are done. Love them.
# 10
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Easy to install and functioned perfectly. Customer has been utilizing it for a year and still raves about it. Thank you
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
# 11
Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 5,000 lbs - Black
I was extremely impressed with the recent technical and customer support from etrailer. Over the weekend, they answered my questions to select the appropriate replacement electric jack for my Airstream. Also, when there was a shipping delay (not etrailer’s fault), Rose provided prompt responses and professional support. I will continue to use etrailer for my RV needs.
Definitely has the power I need however I can't open my tailgate when my camper is hooked up. 5 stars for power.
# 12
Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
Received the Kit in about four days (5 Stars for etrailer). The shipping container was severely damaged (2 stars for UPS), but at least it arrived. Did not appear any parts were missing. I ordered this kit because it was less expensive for the complete kit then to replace both landing gear legs separately. I left the 5th wheel attached to the truck and removed the old landing gear, gearbox, and motor prior to the arrival of the new system. Keep all your parts. The new kit arrived and was very easy and straight forward to install. However the tubular steel expansion rod that connects both landing gear legs was too short. I had to use the my old connection rod. Also the spacer used for the inside of the large side of the connection rod was not included with the kit. Had to use the old spacer in the old connecting rod. I used my old landing gear foot plates and pull pins on both landing gear leg extensions. Once installed, the kit worked flawlessly. I placed red marker tape on the landing gear extensions so not to top out the legs when lifting. Again save all your old parts.
Installation was easy and it works really well product was worth every penny
# 13
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black
Replaced stock Air Stream power jack which started making grinding noises. New 4,000 pound jack easy install and works fine. Using it to lift 25ft trailer and 2500hd Silverado to attach anti-sway bars. Had to mount it sideways due to propane tank cover, but it works great. Had one of these on a larger trailer that a hurricane destroyed. Nice unit and easy install.
Overall the product does exactly what it's intended for and works well. I however assumed that this would be a simple R&R for my camper and did very little installation research other that the video provided on etrailer' s website Sadly it did not fit. Not at all. I didn't take into account that have a double framed hitch toyhauler. The baseplate on the factory leg was a TRIANGLE.....this unit was ROUND. Also the primary shaft was thicker than stock and would not drop down into place I know modifying is frowned upon, but I found that ALL powered hitch legs I found have round mounting plates and it's not mentioned the leg tube is thicker than OEM? Since NOT having a power lift wasn't an option for this camper application...too heavy in the front when ATVS loaded to lift for setting the equalizer hitch tension bars, I proceeded to modify by cutting the rear rounded mounting base ... square. Took off about 1/2 inch. Then I took my metal Dremel sanding bit and increased the hitch leg hole diameter slightly. Took about 1 hr. Dropped it in. Wired it. Tested it. All good. If you can't post this I understand, but take note that some of your website descriptions may need to be enhanced. Thanks!
# 14
Electric Jack w/ Footplate - Drop Leg - A-Frame - 25-1/8" Lift - 3,500 lbs - White
Item arrived a day earlier & in good condition! & was a very easy install ,& is a upgrade from manual one that broke at the handle ,& this is a upgrade for my 2008 22'Airstream Safari! Can't wait for my next outing, Also I like that it comes with a backup manual hand crank in case you need it,& that it was a exact fit for my travel trailer,It's a complete package that needs nothing else.
I purchased this jack to replace my tired 10 year old camper jack . I ordered it at 10:00 AM Monday and as promised by Ian it was at my doorstep on Friday just in time for my weekend getaway . Installation was a breeze . I gave the product a 4 out of 5 for a few reasons . First , I was not able to see the manufacturer of the jack before receiving it . Which made name brand comparison pricing difficult . However I feel pricing was on target . Second , I feel that the jack should come with a battery terminal end connector and new mounting bolts with the hardware that was included . This didn’t pose any difficulty to me as I had hardware at hand but for some it will mean a trip or two to the hardware store . Third , once installed , at least with my truck and trailer , unless the truck and trailer are perfectly aligned and level the jack motor gets in the way of opening the tail gate . On first use I noticed it was much slower than my original but the strength made up for it . This jack had no difficulty or hesitation lifting my truck and trailer for load distribution and anti sway bar installation . I would recommend etrailer and this product . Time will be the final test of its durability .
# 15
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
It looks like a great product am anxious to install them. I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate
# 16
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
Product was an exact fit for my application only problem I had was key inside gear box fell out but easily fixed once I figured it out.etrailer was spot on helping me find correct jack for my ca.per works great
I thought replacing the landing gear would be much harder on my 5th wheel but they when in without a problem and are still working great. The video walks you through the installation step by step. Rick
# 17
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
Great jacks and great fit, however the motor already went out not sure why just quit.
Let me start by saying this review is about the product, not e-trailer. etrailer is great. I love doing business with them. Their prices beat anybody, and the free and FAST shipping is a bonus. Now to the review of the LG-3 landing gear. The pros of this product are they are a direct replacement for the Lippert system on my trailer. No cutting, drilling or welding. They fit in the original brackets. I installed them while camping in about 2 hours with simple hand tools. The cons are they are a direct replacement for the Lippert system on my trailer. They use the same weak motor, that struggles to lift my trailer. The kit was missing bolts and pins and I had to use my old hardware until I could get back to town to buy new hardware. I wanted to go with the Bulldog 10K system, but wanted something that work with my Lippert remote system. The original system failed. I suspect this one will too. Next time I will go with something heavy enough to do the job. Check out the before and after pics and the pic of what can happen when your jacks fail and you have to resort to using hydraulic jacks to lift your trailer. A $4000.00 repair that could have been much worse.
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"