# 1
Yakima JayLow Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.
The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.
# 2
Rhino-Rack Nautic SUP or Kayak Roof Rack w/ Tie-Downs - Saddle Style - Clamp On
After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.
Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.
# 3
Thule Hull-A-Port Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.
I think the Thule Hulaport kayak racks are the best, most secure way to transport your kayaks. I had these on my Xterra and hauled two kayaks up to Cape Bretton park in Nova Scotia, Canada from Connecticut, USA no problem. We were even able to store gear in the kayaks for the trip. I’m so excited to have them for my Crosstrek. Highly recommend these!
# 4
Inno Locker Watersport Roof Rack w/ Crossbar Pads - Locking - Clamp On
Heavy duty. Easy enough to install. Instructions aren't great, but you can figure it out. The crane is a good idea in theory, but could use some design refinement as it only lifts just enough to tuck a paddleboard underneath. The rachet system is great and the rubber coverings for the wires are super helpful for preventing scratches.
This company couldn’t make these products any easier to setup! Had my roof rack built and installed in roughly an hour (double checking on measurements). I’ll gladly do business again if I need any trailer/roof rack needs. Quick to email notifications for updates as well.
# 5
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
Well built and sturdy. Near perfect fit for our Yakima streamline, oval shaped crossbars. Shipping was one day behind quoted arrival date but that wasn't an issue at all.
First experience with purchasing from etrailer. Absolutely felt that my order was personalized which is a nice touch. The Rhino Rack S512 folding JStyle Kayak holders arrived boxed impeccably with no damage whatsoever and the price was great! Fantastic first time experience. Looking forward to using them. Thank you.
# 6
Swagman Contour Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.
Loved the racks, seem very durable. Only downside was that the groove made for the crossbeam was quite a bit smaller than my crossbeams, but they still secured down great. You'd have to have a pretty funky set-up for these racks to not work on your vehicle. Having all the straps/tie-downs included was awesome too. Reccomend!
# 7
Malone BigFoot Pro Canoe Roof Rack w/ Tie-Downs - Gunwale Brackets - Clamp On
The Malone Bigfoot Pro Canoe Roof rack is excellent and is super strong. I have two sets of them now, one for a Malone Aero Bars Car Roof Rack, and one for a Rhino Aero Bars Car Roof Rack (both bought at Etrailer). The quality is first rate, so why the 4 stars? The reason is that the support back of the canoe racks is too high. It only needs to be one inch high which matches the rubber pad. Instead it is 3.75 inches high. Every inch higher than necessary makes it harder to lift the canoe over the backs of the canoe racks. If I could cut them easily I would do it, but it looks like it would be too difficult to cut the metal back down to 1 inch. The Canoe racks are even better using the T-Slot Integration Hardware Kit for Aero Styled CrossBars, MPG915. That kit has 5/8" long (functional length) bolts which fit the Malone Aero Bars Car Rack. For the Rhino Rack, it uses a different kit that has 7/8" long bolts. Using the T Slot allows full use of the entire aero bars.
I bought these brackets for my Ascend H-12 kayak. The kayak transports face-down on Thule roof racks. These high-quality brackets are easy to install/remove and inhibit any side to side slippage while providing a secure tie-down. I highly recommend these brackets for anyone transporting canoes or kayaks on their rooftops.
# 8
Thule Hullavator Pro Kayak Roof Rack and Lift Assist w/ Tie-Downs - Saddle Style - Universal Mount
Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)
2018 Ram 2500, wanted a way to travel with 2 sit on top kayaks, With my wife and i in our late 60's it was taking a LONG tome to get the kayaks on the roof of the bed cover. With these i can do it with a short stool. Also carrying the kayaks upside down keeps the top cleaner and stops the water from getting trapped in the kayak (and raining down on me when I unload them).
# 9
SUP and Surfboard Pads for SeaSucker Monkey Bars - 19-1/2" Long - Qty 2
They were perfect. We had lost a set and had a difficult time locally finding them.
Quality product, does what is supposed to do
# 10
Malone DownLoader Kayak Roof Rack w/ Lift Assist and Tie-Downs - J-Style - Clamp On
I can't lift my kayak onto my roof rack like I could when I was younger. This looked like a perfect answer to keep me actively using my kayak. It is simple to use, but it does take some strength as you have to lift your kayak onto the loader and must lift the kayak up onto the roof rack as it only loads to just before the top, so keep that in mind. The legs need to be about 6" - 8" longer as mine don't touch the ground at the connectors. I can only reach the ground with them lowered to where they are almost out of the holder. They also touch the Jeep, so I am going to have to carry something to fit between the loader and the Jeep to prevent scratching the door paint. I think if the legs were longer and they fit with both the holder/connectors then I think they might not touch the Jeep. I would have given 5 stars if the legs were long enough. It works with both my moulded J rack and my fold down J rack. It works with both style of kayaks, rounded and straight hulls.
About a year ago, I purchased one set of the Malone Downloader w/Lift Assist (MPG114MD-351XL) and second set of Downloader J-Style Folding Racks (MPG114MD) for use on a 2014 Subaru Outback with standard Subaru roof racks. I had no issue with installation and use of any of the parts using the enclosed instructions and online videos. Everything seems to fit properly and securely; no broken, unusable, or missing parts. Over the past year we've use the racks extensively for our 10.5 ft recreational kayaks on both short local trips and longer highway trips. We augmented the roof racks with T-handle hood and tailgate tie-downs and some locally purchased camlock tie-down cords. Everything working great with 10's of racking/unracking episodes. We've only used the Lift Assist maybe 1 of 10 trips when there's only a single person lifting, so can't provide as much feedback. However, the Lift Assist does work exactly as advertised and we're happy with the results. In addition, the friendly and well-informed folks at etrailer.com were a huge help with answering tech questions. Well done!
# 11
etrailer Kayak Carrier w/ Tie-Downs - J-Style - Folding - Clamp On
Easy to install and remove. I ordered 2 and works well for both our 14-foot. and 10-foot kayaks. Padding is good on the bars and folding option a must. Having the straps to include both hood and trunk/rear hatch mounts is a nice addition as it keeps you from having to order these separately. There is some noise from wind as should be expected.
Brought home a new kayak yesterday using this J cradle for the first time. Easy to set up and load. Two complaints: not impressed with the strap buckles - had to tie knots to secure. And the 3-inch bolts weren’t long enough to easily attach the cradle to my Rhino Rack crossbars, so I had to replace them. Also got my finger pinched pretty good adjusting the cradle knobs - my fault for not being more careful, but just saying …
# 12
Thule Compass Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
Wry disappointed in such an expensive rack and kayak carrier. It is extremely difficult to reach the carrier to place two kayaks. We are very uncomfortable transporting the kayaks for longer and highway travel. I would not recommend these to others. We likely will purchase something other in the future. I’d rather put the kayak in a car or pickup truck that they would fit in.
We bought this Kayak rack for my mom to put on her 2016 Jeep Grand Cherokee so her and my dad could haul their kayaks easier. The mounting hardware was a little tricky at first but once we figured it out, it wasn't bad at all. It holds the kayaks in place nicely. Had no issues with them getting loose or moving around. Seems to be built well and they're very happy with it so far.
# 13
Thule Stacker Kayak Roof Rack w/ Tie-Downs - Post Style - Folding - Clamp On
We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.
My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.
# 14
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
The Rhino-Rack 2 Kayak Carrier I ordered from etrailer was easily reviewed and ordered from their website and ALL communication relative to order confirmation and extreme detail included in their tracking was nothing short of phenomenal! The items were packaged with care and arrived intact. These fit our basic Lexus crossbars and is the perfect product for carrying our two (2) kayaks. My hat goes off to the great folks at etrailer -- It doesn't get any better than this!!!
These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.
# 15
Rhino-Rack Kayak Roof Rack w/ Tie-Downs - J-Style - Fixed - Clamp On
Love the quality of the rack and the kayak mounts that I ordered. Five stars! Removed a star for the instructions and for the key for the security locks that broke the second use. The instructions ...work... but take a fair bit of patience to understand. Once deciphered, the mounting goes pretty quickly. Major room for improvement. The key - simple broke in half on the second use. No major stress put on it, just broke lol. Good thing kit comes with two keys so kudo's for that. Have a 2011 RDX. Car handles great with a 14.5 foot 55 lb kayak mounted. Driven up to 50 mph with the kayaks. No noise on the turnpike with just the roof crossbars at 80/90 mph. Overall, I love the rack system and the above two issues aren't show stoppers for me and I'd recommend them to a friend (tho I would help them with installation :).
I installed these as soon as I got them and I’ve got to say, there are some extra holes for screws that are a tad misleading and the pieces that secure it to the cross bars don’t seem super secure. For reference, I do have Rhino Rack’s vortex crossbars so this should fit snug. The rubber tops were tough to get into place and I am worried they’ll snap when I go to remove my rack but Rhino Rack has yet to fail me with their products so I bet it’ll work out great!
# 16
Lockrack Adjustable XL Watersport Carrier - Canoe, Kayak, or 2 SUPs - Side Loading - Universal Mount
The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.
Rec'd earlier this week, so today i will install. The item was obviously a return. The logos are nearly scratched off in places, all the items were loosely thrown in the box, and the 10mm wrench and hex key were missing. i think everything else is there. The keys should be a bright color instead of black, some spray paint will fix that. Anyhoo, i am a little disappointed.
# 17
Yakima SUPDawg Stand-Up Paddleboard Carrier w/ Tie-Downs - 2 Boards
I use these 2-3 time weekly for my SUP I fish off my SUP and this rack is a great investment for quickness and ease of strapping. Thing I like best about etrailer is how fast I get my stuff.
# 18
Rhino-Rack Nautic 581 Kayak Roof Rack w/ Tie-Downs - Saddle Style - Channel Mount
My OldTown Sportsman PDL120 was shifting around to much in very windy conditions. I bought the large Yakima kayak saddles/supports from etrailer.
I recently purchased the Rhino rack below with these boat supports: Rhino-Rack Nautic 581 Rear Loading Kayak Carrier - Saddle Style - Rear Loading - Channel Mount Item # RR581 Also, I attached a Yakima Jaylow kayak carrier, all to a 2019 Toyota Highlander Hybrid. On the 54 inch aero bars, I was able to carry a Hobie Compass Duo kayak (35" beam, carried flat on the Rhino pads) and West Marine Pompano 120 (28" beam, propped up as shown on the Jaylow racks). To have enough width, the Jaylows and the Rhino pads are mounted as far out as they can go, and the straps are looped back under the rack pillars on the car. The bow and stern were secured with hood loops on each side (front diagonal straps on the Hobie), on the front placed under the hood where shown (this is the only place I could find a good metal-metal contact under the hood, and no electronics in the way), and in the back, tucked under the rear door. We did a 500 mile round trip to the beach and back, with no problems at all with the mounts. Little noise, no movement. My only recommendation is to figure out some kind of load assist for the large tandem kayak, to make it easier if one of the folks loading is under 5'8" in height or so. We worked it out, but only after a few failed attempts (especially when the boat is wet, and loaders are tired). Carol C at etrailer provided thoughtful, expert, and knowledgeable tech support for our purchase. Many thanks!
# 19
Malone SeaWing Kayak Roof Rack w/ Load Assist and Tie-Downs - Saddle Style - Clamp On
I am happy with my purchase of the Malone SeaWing with the load assist feature. I use it a lot and it is holding up well. I have square crossbars, and the wing base can be flipped over during assembly to fit square bars perfectly. The load assist really does make it easy to get my 14 and 16 foot kayaks on the car by myself. Another reviewer stated that the load assist feature put black streaks on his thermoformed kayak, and I had the same experience. I fixed that by wrapping heavy duty, double sided Velcro around the areas of contact, and that has worked fine. They are still in place one year later. Four stars because Malone should have covered the load assist sliders in a non-marking material.
The lift assist would not work with a skin on frame kayak. Repeated use would damage the skin. You can see in the pic that the load assist pushes in on the skin, and would not slide all the way into the storage position without lots of pressure on the kayak. Etrailer would not take retuttome inern since I installed the rack, but there was no way to know without trying. So bottom line - don't try to use this on a skin on frame kayak. And don't count on etrailer for returns when they sell a product that doesn't work as advertised.
# 20
Malone DownLoader Kayak Roof Rack w/ Tie-Downs - J-Style - Folding - Clamp On
I had the moulded downloader and needed the folding in order to fit in the garage. The top feed for the tie straps isn't as good as the moulded J-style rack, the strap came out of one, but the kayak stayed where it needed to be. It is easy to raise and lower the rack, but I am not always sure at what angle I am supposed to set them. With the moulded J-style, they are at the perfect angle for holding a kayak. I wish the clamp that goes under the bars were a better fit for the oval bars, but they do send two different size bolts and the longer ones work.
The Malone DownLoader is very good value for the money. The J-style cradle is nice when you have to muscle a kayak on top of a tall crossover or SUV. You can hook the edge of the cockpit onto the base of the cradle and flip the kayak up onto the metal hoop support. Carrier installation and removal is easy and doesn't require any tools. Materials are good, but not great and that's what prevents this product from getting 5 stars IMO. The foam padding is nice enough and has been durable, but the metal plate that attaches the carrier to the roof rails is plastic coated steel and the plastic cracks over time, and leads to rust on the steel plate beneath. Not a big deal, but it might compromise the plate over time. I also wish that the provided nylon straps were longer, and that the ratchet buckles were covered in rubber to protect the roof of the vehicle and the windshield when you're trying to get them around the hull of the boat. We quickly replaced these with longer aftermarket straps that have rubber covers over the buckles. Those minor points aside, the Malone DownLoader kayak carrier gets the job done easily and safely, and does so at a very affordable price point.
What our customers are saying:
"very easy to shop"