# 1
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Good solid hitch, but a REALLY tough install. I have installed several hitches from etrailer and this one was especially tough for several reasons: First, the neither the directions nor video accounted for a dual exhaust muffler(standard.on our 2016 Cherokee Latitude), the chrome exhaust trim or removal of additional screws necessary to drop the exhaust. Second (and most critical), the fit was so tight on the frame I had to jack the hitch up to allow the weight of the car to press it up into the frame. The guide wire for the side bolt became helplessly pinched, making it virtually impossible to access that bolt. FINALLY, after all this, the hitch is still not 100% level; it has a slight tilt to the right!! It should not be this tight of a fit, a d I hate the fact that it's not sitting level!!! Very disappointed.
I was a bit concerned at the beginning on whether or not I could successfully install a hitch on my new Jeep Cherokee. When I saw the installation video you offered there didn't seem to be anything that would prevent me from installing it. I was right ! The hitch actually arrived a day earlier than expected, late in the week and by that weekend I had it installed. The video, ( which YES I watched several times before beginning ) explained exactly what to expect. Your video indicated it was the closet thing to a factory install. That is exactly what I found. Because it was my first time installing a hitch it took me and a friend just under two hours. The results were definitely worth it. Thanks for the great product and all the additional assistance. R Hutchins
# 2
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Very happy with the hitch. Took me longer to install than the estimated time (2 hours) but I am 65 and so is my helper (wife). The directions were perfect. I purchased this so I can put a bike rack on my jeep.
very bery easy to install. etrailer gave me all the tools i need(besides a socket wrench and socket ofcorse) but the screw wires which i was worries that it didnt come with, was included with the package!
# 3
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
This is a quality hidden mount hitch receiver. It was delivered super fast. Their recommend installation link had a place local to me. Lines of Lehigh valley in Quakertown. Perfect installation in a short time. My friend asked me to get an estimate for their car and they are also buying an etrailer and having it installed by linex as well. It looks great on our Jeep Cherokee
I think you suck... I called and told you guys this was the wrong one but you insisted it was correct. After many hours for fighting I brought it to a professional who again verified that the hitch was incorrect for my vehicle. So now that im balls deep into this shit show, they had to just make it fit and will have to fabricate my trim pieces to go around my tail pipes.... I will never do business with you again. Guaranteed fit my ass and the video needs updating as well...
# 4
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
Came 2 days early, didn't take my money till they ship it. Plus I never like to order anything online because I'm afraid it won't fit. But they said it would an it did( 2016 chevy traverse). Also it says 45 mins to install. Sounds About right 10 mins asking the wife an kids to help hold it up with no luck, 10 mins looking for my tools 18mm & 3/4 wrench,10 mins looking at the picture of the instructions because what GUY really reads it? lol, 10 mins putting it on by myself laying on my back in the driveway using my leg to hold it up & 5 mins putting on 1 bolt by the muffler because I didn't read the instructions an lower the muffler out of my way hahahah. P.s is you have soft hands I suggest wearing gloves an waiting for the muffler to cool off because i didn't ??. But all in all it was easy & fast to put on even if your by yourself. Definitely ordering again if I need anything for her car. Thanks etrailer
I blindly ordered a Draw Tite receiver for my 2011 Acadia - based upon reputation. Had it installed and it cost me $100 do have it put on. Recently weather allowed me to proceed to installing my long term (CURT) 2 inch Ball bar with 2 inch ball into the Draw Tite receiver for work needing to be done and found that it would not allow inserting unless use of sledgehammer. I attempted to file down the misaligned (welded on) collar that was forcing the misalignment and was not able to make to make it work. Nichole at etrailer worked with me and replaced the Draw Tite receiver and I found the replacement was properly aligned and my Ball bar does now fit properly. So - presently had over double the cost for the defective unit and replacemetn that I should have. Being 82 year old I can no longer perform the task of handling this work.
# 5
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
Heavy duty for sure, and it's rated higher than we will ever need. However, it is designed to be too close to the muffler and when driven on rough roads the muffler was banging into it. if they had just moved the crossbar another 1/8-3/16" further it would not have this problem. Also the vertical part of the mounting brackets was so tight on the frame rails I had to use a jack to push it up. That made it quite difficult to pull the fish wire through the hole since it was pinched between the frame and hitch. Again, just 1/8" more clearance and I don't think it would have been a problem. The included fish wire worked great. The hardware is robust. etrailer had the hitch for a good price and I will buy from them again.
Perfect fit, excellent quality, bolts and fishlines included. Thank You!
# 6
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
The hitch installed with no issues. I am impressed with the interaction of the web site and tremendous amount of instruction and consumer protection covered to make the measures for a safe installation. Thanks
Installed on my 2012 Highlander and my experience just like many others indicated the holes did not align on the driver side. It took me more than two hour and at the end the wife said why can't you use the car jack. So, that's it. The car jack will take care the issue. You would use the car jack between the spare tire and the other end of the hitch, push it out until the holes line up and you can insert the bolts. And as others mentioned with a small custom cut on the driver side cover panel, you can re-installed it. The passenger side panel can go back in without any modifications.
What our customers are saying:
"Excellent deal for the trailer hitch with accessories. Best deal on the web. Free shipping was the bomb!"