Most Popular CURT for 2016 Hyundai Tucson

No complaints here works as it's supposed to feel solid

solid receiver

I recently purchased this hitch and related wiring accessories from etrailer for my 05 Hyundai Tucson. Following the included installation instructions I found the hitch easy to install. Total install time including the wiring adapter was approximately 1.5 hours without rushing.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

Love this product. Thank you for you support.

great value easy install

Nice and heavy duty. Make sure you order the 1/2" pin when you order this.

We really like the hitch we ordered for our Camry. It was extremely easy to install. Fit perfectly!

Etrailer is great. Good service!

No issues after one year of use. Happy with product

My Mini Cooper is lowered and this unit really helped level out the trailer I am pulling. The product is heavy and solid. I would definitely recommend this item

Heavy duty! I was a little bummed when I found out how much more difficult it was to find a half inch pin for this, but no matter. It is a tad loose inside the hitch, so there's a little rattle, but I doubt it's as noticable as I make it seem. Super classy and a welcome change from the typical draw bar style. Goes great with my Volvo V70 T5. Thanks etrailer.com!

Overly tight on the receiver end bit functions as intended.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.

Have a 2011 hyundai tucson limited, hitch was easy to install, just 4 bolts. Fits great, really sturdy and solid. I had a second pair of hands during install but definitely not necessary. Didnt even have to jack up the car or move the exhaust pipe. Definitely recommend cleaning the mounting holes beforehand with a toothbrush or wire brush and some cleaner (i used wd-40, it works just the same) and screwing in the bolts halfway beforehand to test fit before you're balancing a heavy hitch receiver trying to get the threads to catch. No complaints so far, haven't used it to tow yet. 2

A very nice unit. It is all welded and looks to be very sturdy. It includes the pin and clip

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.

Great product. Fit and finish is excellent. I've mounted the Curt 1 1/4" hitch to my 2007 Mazdaspeed3. Taking the rear bumper off, which only took 30 minutes (maybe a few minutes more than that) made it very easy to attach the Curt hitch to the car. I wanted to compliment the Mazdaspeed3's overall appearance, so, I decided to go with the Curt euro ball mount 11 3/4" . Very pleased with the outcome.

This worked out to be the perfect ball and mount for my purpose- occasionally having to use my car to tow my utility trailer. I got this and the DrawTite receiver hitch for my '99 Monte Carlo and everything went together in less time than the estimated time that had been shown. Very happy with both purchases!

Hitch is solid and install was 2 hours

Here's 2 photos of the finished product. Doesn't stick out very far which is fantastic, because it definitely would have looked bad on the back of a 2 door coupe GTP. As for installation, being a mechanic, all I had to do was remove 2 rear exhaust rubber hangers and the one right behind the fuel tank, lower the exhaust onto a set of jacks to support the weight. Then drilled 2 1/2" holes with a 90 degree drill. The coiled wires included with the parts saved me tons of time trying to get the bolts in. Overall, it was fairly simple to install. Torquing the bolts proved a little difficult. I would recommend you inform the customers that they'll need at least a 10" eye to eye reciever (I have the 11" one on mine) in order to clear the rear bumper and provide some space between the bumper and trailer tongue. As for the wiring, I cut a small slit in the rubber plug under the spare tire, ran some bulk trailer wiring up through it, under the tire, under the floor matting, to the right side of the trunk, behind the tail light. And up under the lid on the right side, is the tail light wire harness/connector. Test light confirmed which wires were hot, tapped into them and all the wires and lights are good to go. Just some extra info for the DIY'er that might be handy on the website so they won't have to search for it! Couldn't be happier with the hitch.

Needed a longer unit to accept a bike carrier.

Just what I ordered.

Just what I needed, most receivers would not allow me to open the tail gate on my 2022 dodge ram without hitting the trailers crank used to mount and dismount the car hauler trailer, this receiver give me the extra few inches I needed and it works perfectly, I tried many local sources but they all came up too short, etrailer is the place to go for all trailer parts, they seem to know and sell exactly what you may need

For a 7,500 lb hitch, I was surprised it didn’t have a wedge support welded on where the flat iron is welded to the square tube.

Not as versatile as a traditional hitch mount and ball, but much neater if it happens to fit your needs. This fits my Subaru Outback perfectly and places the ball at the ideal height for my trailer. One piece means one less thing to fail.

My order got messed up several times. From USPS lost in shipping, wrong part ordered, wrong amount ordered (my fault), wrong part number (printed on label from manufacturer) etc... In the end etrailer managed to make it right!

This was purchased for towing a 7k GTWR utility/landscape trailer with my 2018 Chevy Silverado 1500 WT 4x4. I measured for necessary drop before ordering, and the 4" drop is darn near perfect. It's a great help that the 2-5/16" ball comes complete, installed and torqued properly at the factory. Appears to be quality construction, fits and functions perfectly. I have no complaints or issues.

WHat a difference having the right drop has on handling. A great product - highly reocmmend.

Worked perfectly. Super easy installation and it carried a U-haul 5x8 trailer 1000 miles with almost full capacity on tow-limits. A little disappointed that the connecting rod doesn't fit perfectly into the receiver hitch. So, when there is no weight on the ball mount, it is wobbly and makes an annoying metal-to-metal clinking noise whenever you go over a ditch. You can easily correct it with a piece of cardboard stuffing for cushioning or just take it off when not it use. Great piece of equipment, works perfectly! Super happy with the purchase.

This starter kit was exactly the size I needed for the hitch on my Trailblazer, and has held up beautifully this past year. I'm confident it will last for the lifetime of the vehicle.

I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.

I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!

Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.

I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.

The Curt trailer hitch and wiring harness for my 2016 Highlander was a perfect fit. Installation was a breeze just following the etrailer videos. I opted for the 4" drop ball mount because of the Highlanders ground clearance but the standard 2" drop would have been just fine. Will use etrailer again without hesitation.

I purchased this hitch to pull my utility trailer with. It was easy to order, arrived on time, and simple to install/use. This hitch is built very well and strong, and has a good coating finish on it. Great product!