# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Overall, I am extremely satisfied with the products I bought. Your communications are excellent; shipping was performed in an expedient manner and the tracking of the packages was much appreciated. I'm not sure I'll be buying anything else from you (I can't imagine needing another tow bar again) but will surely recommend your company if asked.
Fits loosely into the hitch, along with a loose fitting pin. Thus, your trailer will constantly rattle and clang every 10th of a mile that you drive. It will drive you crazy and insane thinking that your trailer with your $50,000 boat or camper will disconnect and be left along the highway behind you for all semi-trucks to run over and shred to thousands of bits and pieces.
# 2
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
I was very pleased with the etrailer.com staff's help in choice of hitch, ease of purchase shipping and tracking of the products 98900 and E98866, both products arriving at my residence together the day promised and undamaged. My Grandson and I mounted the hitch today. I backed the car up onto a set of ramps and by removing the piece from the rear bumper as shown in the video, we had very little problems in guiding the hitch in above the muffler to its bolt down point and pulling the wires through the proper holes which I had circled with chalk. I did not trust the video and had constructed a wooden support under the muffler so it did not drop should the hitch slip out of our hands. We did use it to rest the hitch on top of the muffler when our arms got tired until we got the first nut on a bolt on either side in place. Being 70 years old with two back surgeries I would never have attempted this by myself because the class III 2" hitch is very heavy and awkward as the receiver area makes it want to tip down but a short 2x2 support kept it balanced. The video provided is worth mentioning, as it made the job easily understandable. Between prepwork and all it took about 1 1/2 hours. Very pleased.
Bought a trailer hitch and wiring harness for my 2017 Ford Escape. Both the hitch and wiring harness went on very easy, I spent maybe 4 hours with a lunch break thrown in to put the whole thing together.. saved me a ton of money not having to rent a truck and car carrier, and just towing a trailer. Thanks for a great product and a great price.
# 3
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Great product
Looked everywhere for the right hitch tô fit my Ford Escape. Finally found it here. It fits perfect and delivery was fast. Will definitely be ordering from you again. Thank you.
# 4
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
no problem with this part.
Perfect fit for a factory-installed classI II hitch on a 2010 Ford Escape.
# 5
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 6
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This is a huge difference maker for us. I can open the tailgate of our truck with the trailer still attached, and helps minimize any body damage if my backing up is not good.
# 7
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 8
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
No problem. Exactly what I needed
Looks great, if it holds up under use, then this is a great buy. Heavy duty, well spend money. I like the key lock, I have never seen this before but I can see you may have a need for locking your hitch at night in a motel parking lot or somewhere when you have to leave your hitch in your auto unattended.
# 9
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Very well made hitch and already put together. Very fast response on the order, got the order in only a few days.
This product came with a very thick powder coating, no scratches on paint. Seems like it's going to hold up to some abuse
# 10
Reese Trailer Hitch Starter Ball Mount Kit
Feels strong .
# 11
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
no problem with this part.
Works great with my new Kurt receiver hitch and the drop is perfect for a level tow on a '08 Ford Escape.
# 12
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Great product
Works perfectly. Needed a tow bar with very little rise and would clear the bumper. Thankfully, etrailer has a huge selection of equipment so you can find the right piece.
# 13
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Just as advertised!
I was very pleased with the etrailer.com staff's help in choice of hitch, ease of purchase shipping and tracking of the products 98900 and E98866, both products arriving at my residence together the day promised and undamaged. My Grandson and I mounted the hitch today. I backed the car up onto a set of ramps and by removing the piece from the rear bumper as shown in the video, we had very little problems in guiding the hitch in above the muffler to its bolt down point and pulling the wires through the proper holes which I had circled with chalk. I did not trust the video and had constructed a wooden support under the muffler so it did not drop should the hitch slip out of our hands. We did use it to rest the hitch on top of the muffler when our arms got tired until we got the first nut on a bolt on either side in place. Being 70 years old with two back surgeries I would never have attempted this by myself because the class III 2" hitch is very heavy and awkward as the receiver area makes it want to tip down but a short 2x2 support kept it balanced. The video provided is worth mentioning, as it made the job easily understandable. Between prepwork and all it took about 1 1/2 hours. Very pleased.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."