# 1
MaxxTow Trailer Hitch Receiver Adapter - 2" to 1-1/4" Hitch - 11" Long
Perfect solution to the problem of not enough clearance space for my bike rack in my dealer installed hitch on my 2019 Hyundai Santa Fe. I had to ream out one of the holes to accommodate a larger pin for stability, but no problem. Highly recommend.
Just right for my bike rack.
# 2
Hitch Reducer 2" to 1-1/4" Trailer Hitch Receiver
This has worked great to reduce my 2" hitch so that I can continue to use my 1 1/4" Thule bike rack, and I like that it doesn't extend out much from the hitch. After my last trip though, the inset separated from the larger piece. I can still use it, but without the smaller piece fixed in place, I can't put it on the car first and then slide the bike rack into it since the smaller piece slides, and it's impossible to line the holes up. It's also rusted more than I expected. It wasn't inexpensive, and I was hoping it would last longer. I've used it for maybe a dozen trips.
Perfect fit BUT the inner tube broke away from the outer tube after about a dozen trips. One small weld on the outside corner is all that holds it on. The small amount of play must have been too much for it. I was even using an anti-rattle lock pin. Very disappointing due to the price point. And now it’s unsafe to use as it could slip right out of the receiver.
# 3
Hitch Extender for 2" Trailer Hitches - 8" Long
Just received my 80307 Hitch Extender for 2" Trailer Hitches - 8" Long. My newly upsized spare tire had been preventing the use of my hitch rack. Was very pleased with the etrailer service and the ease of using the website. The excellent descriptions, photos, and even videos really help shopping for these types of specialty parts. Shipping went well and expediently. I trial fit the extension with my hitch rack today, and the photos are attached. It fit well and did the trick. I drove around and heard no rattles from it at all.
Prefect fit well
# 4
Malone 2" Dual Purpose Hitch Receiver
Used the Malone 2" Dual Purpose Hitch Receiver to have a bike rack with two bikes on the upper Receiver and a 21' bassboat on the lower Receiver. Ran down to Florida Everglades, Florida Keys and back home. Almost exactly 4,000 miles. Hitch worked perfectly. I did find that you can not "jacknife" the boat as much or the bow of the boat will touch the bikes on the rack but that is to be expected. Hitch was quiet, strong and exceeded my expectations. Easy to install and looking forward to using it again in a month for another 4,000 mile road trip. Note: I drive fast and the roads are not always perfect. This is a sturdy Hitch Receiver. Hope this review helps you. Sorry, crummy photo as the Receiver is a "set it and forget it" product. Be well.
I bought this Dual Purpose Receiver at Twice the price of that Big online company because of reviews from owners that bought on both sites. After evaluating the reviews, I chose to go with etrailer because I have come to trust them as a company that gives you a great product that they will stand behind and they appreciate your business. I haven’t used this receiver yet, but can look at it and I am comfortable that I made the right choice. I will follow up with another review after I use it.
# 5
Hitch Extender For 2" Trailer Hitch Receiver 7"
Incredibly fast delivery. I paid more for this hitch extender but it’s obvious why. Solid construction and therefore a heavier weight rating.
Allows me to use my back rack and small boat trailer without having to remove the spare tire on my Jeep Wrangler. Works well.
# 6
Roadmaster Dual Hitch Receiver Adapter, 2" or 4" Drop/Rise
Exactly what I needed. Now able to add storage box and still pull tow Dolly.
Etrailer’s customer is actually customer service. There’s real people who are there to help. Kate helped me get my order the next day after I realized I accidentally switched the billing and shipping addresses on the order form.
# 7
Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver - 7" Long
Fantastic Product. Saved me from having to buy a brand new bike holder for my new car with a different hitch size.
Professional, delivered a day early. As promised. What more can you want.
# 8
Draw-Tite Hitch Extender for 2" Hitch Receivers - 18" Long
I was surprised by just how solid and heavy it was made. Just what I needed to move my Bobcat UTV hitch back to I can use it as my yard dog to shift my trailers around and not worry about the plastic tailgate nor the plastic bed getting damaged. The hitch sits under the bed and this extends it out so it is useable.
The hitch extension worked perfect. The only one that was 18" pin to pin which was exacty what I needed to make this combo work. Dual hitch to start. Top whole a luggage rack to haul coolers and the bottom for the bike rack. Thanks etrailer.
# 9
Curt Hitch Extender for 2" Trailer Hitches - 14" Long
The items I ordered will allow me to adapt my utility trailer for transporting my sea kayaks. Curt and Hopkins are both quality manufacturers. On a shipping note, the box arrived at the Post Office broken wide open. Your shipping folks need to wrap small, heavy, items in bubble wrap. Then stabilize it with foam peanuts. Just putting it in a box then stuffing the box with craft paper does not cut it. Items were not damaged so I am good to go.
Works great and reasonably priced. etrailer Customer Service is absolutely the very best. My first shipment arrived missing the hitch extension. Customer Service quickly responded to my communications and shipped a replacement the same day. As you can see from the photo the hitch extender is perfect for my Polaris Ranger and allows me to use my small lawn n yard implements. I highly recommend etrailer.
# 10
Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver (Class II Only)
This adapter allows us to use a bike rack we have across all our cars. It is perfect for light duty applications, easy to use and it can be stored in the trunk until you need it. I would definitely recommend it.
It works great I kinda wish I had gotten two of them ‘mmmm
# 11
Curt Trailer Hitch Receiver Adapter - 1-1/4" (Class II) to 2" - 6" Long
The Curt C45785 1.25 inch to 2 inch hitch adapter seems well-constructed, but does NOT fit the current SPA Volvo OEM 1.25 inch automatic retractable hitch receptacle (mine is on a 2020 V60 Cross country). The lock pin hole doesn't go back far enough to accommodate the pin -- see photo.
Great product from an even greater company. ETRAILER has the knowledge and products to solve most any trailering problem.
# 12
Reese Titan Reducer Sleeve 2-1/2" to 2"
This ain't pretty. But size does matter. The 58102 2" X 2 1/2" receiver adapter hits the spot. It fits nicely into the 2 1/2" receiver with, at most, 1/8" space "slap" room. It's almost full length front to back inside receiver providing plenty of support for my 2" weight distribution system without slap. I have not hooked up my Forest River 29'4", 10,7 75 lb. GVWR Puma tow behind R/V but I do not have any fear of this well constructed, perfect fitting receiver adapter. The people at etrailer are there, willing and able to assist you. I have personally found that, if the C.S. Rep doesn't know the answer, she/he will find the answer and report back to you, in my case within minutes. My purchase was delivered (snail mail) within 5 days and In excellent condition. I will report back shortly after a trial run hooked up.
This fits a Curt 2 1/2 receiver perfectly. Allows me to use receiver with my various drawbars for different trailers when I am not using the Forklift hitch box extension.
# 13
Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver with 5" Rise
Thank you for the personal touch on the order. Not many company's do this. This is a good product and a good price. My car sits low and we needed to raise the carrier up. Looks like this will work out.
I bought this adapter so that I could mount a bike rack on the back of my 2012 Honda Civic. The adapter got the bikes high enough so that they wouldn't hit the pavement when backing out of my driveway and transitioning to the street. The product is definitely strong and well made. It was put to the test with a very heavy steel thule bike rack that was definitely heavier than all 4 of the bikes that were mounted on it. The fit was precise so it didn't hit my rear bumper as well.
# 14
Roadmaster Dual Hitch Receiver Adapter, 2 " or 8" Drop/Rise
Perfect for my application.
Works great! I use it on my motorhome to carry my bikes with a Rocky Mounts Carrier and flat tow my car with my Blue Ox system. It places the bike carrier at an optimal height over the front of the car but my may be different for other bike carriers. Very sturdy and seems to be quality all around.
# 15
Curt Trailer Hitch Receiver Adapter - 2" (Class III) to 1-1/4" - 4" Long
The fact that it's steel is a plus, and it extends the hitch so that the bike rack that's attached now is far enough away from the hatch to not bang against it. Great product!
Ordered for our Kuat rear mount bike rack, as our SUV had a larger hitch receiver. Well built, clean machining and a perfect fit. Fast shipping and exactly as advertised. Great communication surrounding the order. Couldn't recommend more.
# 16
Curt Extender for 2" Hitch Receivers -18" Long
I got this hitch extender to put on my camper so that I could mount my bike rack. It worked like a charm!! The bike rack and bike were super solid on the trip cross country!!
First off, I love Curt products. When I found this item at Etrailer at this low price I was shocked. I was prepared to receive a knock off. I tried my luck and was amazed the product not only showed up at my doorstep the next day but is a very high quality Curt product. My handyman was working on the house and he couldn’t believe the quality at that price. Thanks Etrailer! You are my new go to for my traveling needs.
# 17
Yakima StraightShot Hitch Extension - 2" Hitches - 7-1/4" Long
Works fantastic. Gets the trike rack out far enough to open the tailgate and canopy door.
Needed an extension to get the bike rack out past the large spare tire on the jeep. Worked great!
# 18
Roadmaster Dual Hitch Receiver Adapter for Tow Bars - 2" Hitches - 2-1/4" Rise/Drop
Beefy. I have no doubts of the capacity of either side of this hitch adapter, there's plenty of weld to hold it all together. Very few options will provide minimal drop (for an off-road trailer) and minimal rise on the other side for an additional bike rack or cargo carrier. Jeeps are tough since you need to be able to open the gate. This one clears no problem. My spare is up on a slant back carrier, but I think the stock spare should clear as well. Get you a "Trimax THC200 Universal Anti-Rattle Clamp Fits 2" Hitch" and this thing is solid as stone.
The hitch has held up over Alaskan roads towing a jeep, but it does not sit level in the receiver so the tiny little bit that it sags is exaggerated when the tow bar is connected. Paint starting to peel with wear after a year.
# 19
Brophy Hitch Reducer and Extender - 2-1/2" to 2" Trailer Hitch - 7" Long
We were looking for a solution to haul our utv when pulling our camper. This extender allowed us to leave the tailgate down and still have enough clearance to not damage the tailgate. Downside--this extender amplifies the amount of movement with the hitch. This is more than a simple hitch clamp could fix. I added several modifications to completely eliminate the hitch movement. We have taken several trips since the installation and no issues with pulling the trailer. We did have to extend the safety chains about 4 links. Overall a good product and it accomplished the goal. As always,etrailer personnel are knowledgeable, easy to deal with and have quick shipments.
The hitch adapter solved my problem of hitting my tail gate while making sharp turns.
# 20
Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long
Who do I contact about getting the right extension bar? The one I ordered Is a 2 1/2 inch which I need a 2 inch to slide into my receiver or if you guys have a 10 to 12 inch, 2 inch extension so I can connect it I sent a photo of the end that is 2 1/2 which I need it to be 2 inches to slide into my receiver
I recently swapped out the stock 2" receiver for a 2-1/2" to allow me to purchase and use this extension to get past the end of my Lance 1010 Camper. I believe I will have no issues now towing any trailer (within allowable spec's) or carrying my motorcycle carrier. Great quality piece. can't wait to try it out...
Viking Solutions Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today, on our 2014 Hyundai Santa Fe, we're doing a test fit of the Viking Solutions Stack Rack Cargo Carrier, that part number is 310-VSR001. Now, the bottom basket is going to measure 32 inches wide by 17 inches deep, and it has a weight capacity of 300 pounds. We're going to start by taking a few measurements here, then we'll go over a couple features. First is going to be overall what we're adding to our vehicle. It's going to be about 24-and-a-half inches. Ground clearance to the bottom of our basket is going to be about nine-and-a-half inches. Our closest point is going to be about two-and-three-quarter inches away. Now, this basket is going to be great. It's got two levels.
Stromberg Carlson Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe, we're doing a test-fit of the Stromberg Carlson 23 by 60 Cargo Carrier. That part number is CC-100. It has a 500-lb weight capacity and was designed to work with 2" hitches. While we have it on our vehicle, the first thing we're going to do is take a few measurements. Our ground clearance is going to be first, we're going to go right up under here to the bottom of this bolt, at about 9" there. Overall to our vehicle, we're adding about 26-1/4", and our closest point here is going to be about 2-3/4" away there. With our Santa Fe, we do have a single, passenger side exhaust here, it comes just about straight out and level with the carrier, take a measurement here, it's going to be about 6-1/4" away.
MaxxTow Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe, we're doing a test fit of the Maxxtow 48 by 21 cargo carrier. That part number is MT70422. Now, this has a 500-pound weight capacity and is designed to work with two-inch hitches. The first thing we're going to do here is take a few measurements. We start off with our ground clearance. We're going to have about 10 1/2 inches there.
Lets Go Aero Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe we're doing a test fit of the Let's Go Arrow Gear Cage Cargo Carrier. That is 48 by 32, has a 300 pound weight capacity, and it's designed to work with 2 inch hitches. We already have it loaded up on our vehicle, we're first going to start off by taking some measurements here. Our ground clearance is going to be first, just up under our carrier, we're going to have about 9 3/4 inches of clearance. Overall to our vehicle we're adding about 39 1/2 inches. Our closest spot is going to be about 5 1/4 inches away there.
Curt Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today in our 2014 Hyundai Santa Fe, we are doing a test-fit of the Curt Folding 20/60 Cargo Carrier. That part number is C-1-8-1-5-1. Now, this has a five hundred pound weight capacity, and is designed to work with two inch hitches. The first thing we are going to do, is take a few measurements here. Our ground clearance is going to be first. We are going to have about eleven and a quarter inches of clearance.
Curt Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe C18150
Today on our 2014 Hyundai Santa Fe, we're doing a test fit of the Curt 20" by 60" cargo carrier. That part number is C18150. We already have our carrier here. This has a 500 pound weight capacity and it's designed to work with 2 inch hitches. While it's on our vehicle, we're going to take a few measurements to start off. Our ground clearance here is going to be first. We're going to have about 13 1/4 inches.
Pro Series Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe Sport we're going to be doing a test fit on the Pro Series Solo. This is a 31 by 47 cargo carrier. It's been designed for use with 2" hitches and it's going to offer a 400 pound weight capacity. Part number on it is PS1040100. Now this is one of the larger cargo carriers that we offer here. I would recommend getting a second set of hands to help you get it installed onto the vehicle, but if that's not available for you I have developed a little bit of a method of getting it in here as a single person. What we're going to do is just bring the shank of the carrier in.
Surco Products 24x60 Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe Sport we're going to do test fit on the 24 by 60 Surco Cargo Carrier. Now they've designed this for use in 2" hitches. It offers a 500 pound weight capacity. Part number on it 52018. To begin our test fit we need to slide the shank of the carrier right into the receiver tube of our hitch. Slide it in far enough so that our pinhole lines up with our hitch pinhole. Once we have those in line we're going to slide through our standard 5/8 pin.
MaxxTow Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe MT70107
Today on our 2014 Hyundai Santa Fe we're going to do a test fit on the 17 by 50 MaxxTow Compact Cargo Carrier. They've designed this for use with 2 inch hitches. It still offers a 500 pound weight capacity. The part number on it is MT70107. To begin our test fit we're just going to slide the shank of carrier right into the receiver tube of our hitch. We'll line up our pin hole with our hitch pin hole. With that in place we'll take a standard 5/8 pin.
Curt 24x60 Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe we're going to do a test fit on the 24 x 60 Curt Folding Carrier. Now they've designed this for use with 2-inch hitches. It offers us a 500 pound weight capacity. Part number on it is C18153. Now to begin our test fit we want to slide the shank of our carrier into the receiver tube of our hitch. As we do this we'll keep an eye on the pinhole in the shank to see when it lines up with our hitch pin hole. All right with that in line we're going to take our standard 5/8 pin, well slide that in just like that.
Curt 17x46 Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe we're going to do a test fit on the Curt 17 by 46 Compact Cargo Carrier. This has been designed so we can use it with 1 1/4 or with 2 inch hitches. It has a 500 pound weight capacity. Part number on it is C18145. This is one of the, as the title implies, one of the more compact cargo carriers that we offer so it might be a really good choice if you don't have a lot of room to store one but still need the utility of it. To begin our test fit, as you see, we just slide the shank into the receiver tube of the hitch. We line up our threaded hole with our hitch pin hole. Once we have those in line we've got a anti-rattle bolt that we're going to thread in.
Rola Dart Hitch Cargo Carrier Review - 2014 Hyundai Santa Fe
Today on our 2014 Hyundai Santa Fe we're going to do a test fit on the Rola Dart. This is a 23 by 56 folding cargo carrier. It's been designed for use with 2" hitches and it offers a 450 pound weight capacity. Part number on it is 59550. Now to begin our test fit we're going to slide the shank of the dart right into the receiver tube of our hitch. We've got a threaded hole here. We need to line that up with our hitch pinhole.
What our customers are saying:
"very easy to shop"