# 1
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Thank you etrailer for the quality products I received early last year. We needed a trailer hitch to install on our Subaru Forester for our move from Gig Harbor, WA to Spokane. We received the hitch hardware including the tow bar and electrical harness. The entire process took 4 hours. The installation process went off without a hitch (bun intended) using detailed videos I found online. Thank you etrailer.
Didn't receive the storage case for hitch
# 2
Curt Class II Drawbar - 3/8" Rise, 1" Drop - 7-13/16" Long - 3,500 lbs
Well this install on my '05 Outback Wagon was more challenging than the last one I did on my '05 Baja but all's well that ends well. Haven't done the wiring yet because the hardware install took all day but confidence is high. These guys make a quality product!
Excellent quality and construction. Matches perfectly with my Curt hitch. Highly recommend. Also, etrailer has the best customer service of any online retailer I've ever shopped at.
# 3
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
Haven’t used it yet, but looks good. I’m not sure what height offset I need, so this kit gives me several options, plus two ball sizes. Really good value.
I installed the draw tite hitch onto my brand new 2018 Subaru outback. I'm 68 years old, not as strong as I was, but proud to say I did the job all by myself in about 4 hours. Here are some tips you may find useful. Watch the video-it’s pretty good. I had difficulty getting the exhaust system down and worried about getting it up again from the moment I got it down...read on-help will follow. I bought a stepup drill bit which worked great for drilling the hole in the chasis. I clamped the hitch onto a floor jack, then rolled it and raised it into position. Used metal shears to easily cut out the heat shield as per the video. Your inclination will be the screw the fishing tool provided all the way up the carriage bolt. That won’t work; just screw it on to the tip of the bolt. I couln’t get the exhaust hangars in place even after lubricating them with wd-40. I dropped the rubber hangars into undiluted liquid car wash soap which made them much more slippery than the wd-40. After that the rubber hangars slipped into place pretty easily-that’s my best tip. Finding the electric connection plug for the wiring harness was almost as hard as installing the hitch. I was very happy with how the job came out. Good luck.
# 4
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
# 5
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This is a huge difference maker for us. I can open the tailgate of our truck with the trailer still attached, and helps minimize any body damage if my backing up is not good.
# 6
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Just your basic ball mount, the product is just like most 2” Hitch ball mounts, the service wasn’t very good though. Ordered on June 15th (product was in stock) took them 6 days to send it out, took another 6 days in shipping and got all the way to my post office two days before leaving on vacation (I needed it for the vacation) and the post office said “box was empty and they notified seller” etrailer sent a new one (got here a week after my vacation) in a damaged box (packaging is horrible, little bit of paper in a box with a 5 lbs ball mount) almost lost this one too. I don’t believe I’ll be using etrailer in the future (had issues before)
Does the job, however there's a lot of play when hitch mount is inserted into the hitch and when towing with an empty trailer. Very loud. Have to buy a silencer that goes around and secures the product.
# 7
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 8
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
Delivered missing the retaining clip
Keep with spare tire out of weather to prevent rust.
# 9
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 10
Reese Trailer Hitch Starter Ball Mount Kit
I needed an very specific ball mount(class I, 1/2" rise, 2" ball). etrailer had what I needed in stock and available to ship next day. I had the thing ordered in 60 seconds. Wish I wouldn't have waisted my time and gas shopping at my local hardware stores only to find they didnt have what I needed.
# 11
etrailer Ball Mount Kit - 3/4" Rise or 2" Drop - 7,500 lbs
Easy to install and they feel really sturdy. Definitely recommend buying them with the carrying case as it makes them super convenient and easy to stow away when not in use.
Great product! Makes it much easier to switch ball size with 2 different trailers, one needs 1 7/8 ball and the other a 2" ball. solved the problem of needing to ball sizes. Also nice bag to keep and carry the draw bars in.
# 12
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 6-3/4" Long - 2,000 lbs
I wrote 2 days ago and haen't heardafom anyone so I guess you only want reviews-. Here is what I wrote Steve, the class 1 hitch doesn’t fit the trailer hitch either. I don’t understand the continuing problem with all of the Curt hitches we have tried including the last draw hitch you selected and shipped, which I now need to return after H. Idalia passes, I want to point out that I initiially ordered somewhere on line a Maxxhaul adapter so I could move my 2” trailer until I sell it and it fit perfectly. I NEVER expected to have so much trouble getting a ball hitch to fit the 1.25 hitch recommended by etrailer for my car. Aren’t you glad I am writing an email rather than make star comments? I know that someone writes these things for ‘you’ and you don’t necessarily do the hands on so please direct this problem to someone who is supposed to make these product directives and solve this $[XX] attractive trailer hitch problem so I can haul my lawnmower in for repairs when needed on my utility trailer designed for doing so. Doesn’t Drawtite have a ball hitch for level hauling a trailer rather than Curt which is too thick. The powers that be need to rethink OD (outside diameters) vs ID (inside diameters) in their trailer connectors, screw the rattling! PS don’t forget arrangements for the return of the recommended draw hitch.
Great price! Amazingly fast service! The drawbar was a very tight fit in the hitch until I scraped off some of the paint at the end; then it was perfect.
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"