Is There Trailer Bearing Kit With Bearings L44649 & L68149
Updated 02/03/2026 | Published 07/26/2024
Question:
Im wanting to change out bearings, races and seals in my dump trailer. I contacted mfg of trailer and was informed outer bearing is L44649 and inner bearing is L68149. Was hoping to find a kit with all that is needed but so far all I've found are kits with two of same bearings. Do I just need to buy all parts a la carte? thanks. Jayme
asked by: Jayme R
Expert Reply:
Hi Jayme,
Thanks for that info and there is a bearing kit with the L44649 and L68149 bearings you need; the correct kit is the following:
- Hub Bearing Kit # BK2-100
This comes with both of those bearings as well as their accompanying races, the correct grease seal, along with a cotter pin and washer.
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: grease seal 58846
- Search Results: 10~19 grease seal
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: grease cap
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Search Results: timken trailer bearings races seals caps
- Search Results: bottle jack
- Search Results: spare tire mount
- Search Results: grease lubricants sealants adhesives
- Video: Step-By-Step Installation for the etrailer Hub Bearing Kit - Utility Trailer
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Video: Trailer Idler Hub Assembly for 3,500-lb Axles Review
- Shop: Curt Venturer NEXT Trailer Brake Controller w/ Plug-In Harness - Up to 3 Axles - Time Delayed
- Article: Most Popular Wheel Bearings
- Shop: Timken Grease and Oil Seal - Double Lip - I.D. 1.719" / O.D. 2.565" - 473336
- Q&A: What Alarm Setting Should Be Used When Setting Up TST TPMS for RVs
- Video: Timken Bearing Kit Installation - Enclosed Trailer
- Video: A Closer Look at the Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles
- Q&A: Replacement Hub and Drum Kit for a Lippert 3,500 lb Axle
- Q&A: Is There a Way to Tighten the Fabric and Fix the Tension on a Solera RV Awning?
- Q&A: Does Race Need To Be Replaced If Installing New Bearings
- Q&A: How to Retighten the Awning Fabric On a Solera Powered Awning
- Q&A: Do Hub Races Have to Be Replaced Each Time Bearings Are Changed
- Q&A: Is There a Special Tool Or Trick To Installing Trailer Grease Cap On Trailer Hub?
- Article: Trailer Wiring Diagrams
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: All About the Grease Seal
- Video: Comprehensive Review: Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger
Jerred H.
2/3/2026
Hey Jayme, how did things go with the BK2-100 bearing kit for your dump trailer? Did it have everything you needed to swap out the bearings, races, and seals? Your update could make it easier for the next person doing the same job.