Replacement Fenders for a Sundowner 737 Horse Trailer

Question

Question:

Sundowner 737 horse trailer. measured 73 10 20

asked by: Richard H

0

Expert Reply:

Hey Richard, thanks for reaching out!

The Tandem Axle Trailer Fenders w/ Backing Plates # HP32VR measuring 72" long x 9" wide x 20-1/2" tall is the closest thing that we have to those exact dimensions.

These fenders are designed for 14" and 15" wheels so if that's what you have then this should work just fine.

expert reply by: Jon G

0

Answer 1

The only thing the Solera Hybrid RV Awning #LC725517 does not come with is an awning rail. Your RV may already have this as most do, but if not we offer one separately as part #LC715217.

view full answer...

Answer 2

While we might not have an exact replacement we do have two options that might work depending on the spacing of your axles. Part #HP64VR is design to fit 16" wheels and is 9" Wide x 68" long x 17" tall. Part #HP74VR is also…

view full answer...

Answer 3

Do you have a crew cab or a regular cab? Torklift is really particular with their fits but with that last bit of info I should be able to see what solution would work.

view full answer...

Answer 4

Thanks for all of the information Daniel! The Hellwig Big Wig Rear Anti-Sway Bar item #HE24MR will definitely fit your 2024 Ram 3500 diesel. This will work with both 2WD and 4WD models and is also compatible with the dually models as well. I have…

view full answer...

Answer 5

Hey Sam! If your Ram truck has the factory puck system you won't need a set of rails to install an Anderson Hitch. The Andersen Aluminum Ultimate 5th Wheel Connection 2 Gooseneck version item #3220 will attach directly to the gooseneck ball. If…

view full answer...

Answer 6

Hey Chris, Our Fitguide can be a bit confusing sometimes. Essentially the whole category is broken down into whether they fit diesel or non-diesel models. Since the EcoHitch Hidden Front Mount Trailer Hitch Receiver #EH37FR fits both gas and diesel…

view full answer...

Answer 7

Hi Andrew; the Hellwig Big Wig Rear Anti-Sway Bar #HE24MR is specifically designed for Ram 3500 models with a diesel engine like yours. It is also a fit for the dually models so you can install it on your 2024 Ram.

view full answer...

Answer 8

Hey Randy, we have what you need but you will need to measure the width of your pin box to determine which capture plate you need. If it's 13-3/8 inches wide you'd want the part #PUL26RR or if it's 13-5/8 inches you'd need the part…

view full answer...

Answer 9

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 10

Hey Dan, thanks for reaching out! If you have the Progressive Dynamics 4000 Series System #PD4060K then it looks like removing the black and white wires will disconnect the converter section (see attached photo), which charges the battery. I do…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Hi Mark; there may be some TorkLift tie-downs compatible with those running boards but it depends on your total configuration. For example, you can use the TorkLift Tie Downs - Custom Frame Mount - Front and Rear #TL66PR if you have the 8' bed…

view full answer...

Replacement Fenders for a Sundowner 737 Horse Trailer

Product Page this Question was Asked From

Continue Researching