Replacement Hub and Brake Assemblies that Fit Sure Trac 3,500 lb Axle

Question

Question:

I have trailer with 3500LB Sure Trac axle that I need complete new brakes for. Will the following work? AKEBRK-35-SA AKHD-545-35-K Thank you

asked by: Sam G

0

Expert Reply:

Hey Sam, so from previous customers we have determined that the Sure Trac axles use the standard trailer axle components so yes the brake assemblies part # AKEBRK-35-SA and the hub part # AKHD-545-35-K would fit and work great.

expert reply by: Jameson C

0

Answer 1

Hey Zach, since you have a 5,200 lb trailer axle the correct bearing kit you'd need is the part #BK3-300. In order to pick out the hub/drum you'd need I would also need to know the wheel bolt pattern of your hubs so that your wheels would…

view full answer...

Answer 2

Hey Phillip, since we know you have 3,500 lb axles we can help but it's not based on the VIN. Since we don't know what brake assembly brand you have on your trailer but we do know capacity the correct replacement assemblies are the part…

view full answer...

Answer 3

When adding brakes to a trailer the first thing you will need is to determine if there is a brake mounting flange on the axle. If you do not have a brake flange I recommend part #4-35. This should be welded in place by a professional welder because…

view full answer...

Answer 4

Since the trailer was off of the ground it would not take much voltage to stop the wheels from spinning so they may be getting power but they may not be getting enough power due to a short or wiring issue. But 9 times out of 10 weak trailer brakes…

view full answer...

Answer 5

Hey Jared, If your axle has a brake flange like I have pictured below then you would be able to mount a 3,500lb brake assembly #AKEBRK-35 (manual-adjust) or #AKEBRK-35-SA (self-adjust). You'll also need to replace your idler hubs with drums so…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Hub and Brake Assemblies that Fit Sure Trac 3,500 lb Axle

Product Page this Question was Asked From

Continue Researching