Recommended Replacement Handle and Pin for a RAM 8000 Series Jack

Question

Question:

I’m searching for the Handle and pin for the RAM 8000 series

asked by: Raymond B

0

Expert Reply:

For your RAM 8000 Series jack # TJD-7000S, you can use the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks # TJD-7000S-HD for a replacement handle and handle pin.

If by pin you were actually referring to the footplate keeper pin, then you'd need the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-PN as well.

expert reply by: Bryce D

0

Answer 1

The 8000 Series jack is #TJD-7000S. The replacement gear kit is #TJD-7000S-GR. If you'd like to verify you can measure the gears on your jack. The small gear is 1.331 inches for the outer diameter and 0.505 inches for the inner. Then the large…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hi Hayden; that bolt pattern is really uncommon but I believe it can be found on some really old Airstream trailers. There are no modern replacements that will match. The best option is to replace the hub with one that has a common bolt pattern like…

view full answer...

Answer 5

I spoke to my contact at Pacific Rim, they said the correct replacement lower flange bushing and washer for your 8,000 lb Ram jack will be the Replacement Sidewind Handle Shaft Bushing for etrailer and Ram Square, Direct Weld Jacks - 7K…

view full answer...

Answer 6

Probably not unless you want to cut that round hole into a 2-1/4" square. The Square A-Frame Jack w/ Footplate item #e74VV is designed for a-frame trailer's that have a square cut out not the standard 2-1/4" circular cut out which I am…

view full answer...

Answer 7

Trailer ramp spring #362SW61 could work provided that the interior of the trailer is wide enough for the rod (the rod can be trimmed down as low as 48 inches). The capacity of this spring is 120 pounds so it will help when both raising and lowering…

view full answer...

Answer 8

Hey Rudi, the etrailer brake assemblies part #AKEBRK-7-SA that you referenced is the correct place to start as that is correct for a 5,200 lb axle. Next you will need hub drums but that will depend on the wheel bolt pattern you have. If it's a 6…

view full answer...

Answer 9

The number on the lens is not a part number. It is a rating for the lens/light. Based on that number it looks like the best match we have is #A31RB which is rated SAE AP2 86. The A in the number just means that it has a built-in reflector.

view full answer...

Answer 10

Hey Adam, 24-5/8" is a standard sizing for 2,000lb leaf springs so the 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles - 24-5/8" Long #e69SR is what you need. It unfortunately doesn't look like we offer a slipper spring…

view full answer...

Answer 11

Hey Matthew, so we have a hitch that fits your 2011 Mini Countryman like with the Curt #C11333 but the hitch part number you referenced does not fit your vehicle.

view full answer...

Recommended Replacement Handle and Pin for a RAM 8000 Series Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching