Replacement BOLT Lock Cylinder For An ARE DCU Cap On A 2016 Chevy Colorado

Question

Question:

do you sell new/replacement BOLT lock cylinders for a 2018 ARE DCU pickup cap from a 2018 Chevy Colorado that is now on a 2016 Chevy Colorado, thank you

asked by: John G

0

Expert Reply:

A 2016 Chevy Colorado should have a center cut transponder key so you would need the Replacement Lock Cylinder for BOLT Toolbox Latch - Codes to Center Cut GM Key # BL7023480. This is just the replacement lock cylinder so if you're needing parts to retrofit the ARE DCU cap you'll need to reach out to BOLT to get the correct components to swap over to this style lock.

expert reply by: Kevin C

0

Answer 1

Congrats on your new purchase! Since your A.R.E DCU topper has the BOLT cylinders you'll want to use the Replacement Lock Cylinder item #BLT79FR. This cylinder will work with your 2018 F-350's key. To secure the cylinders in place you will…

view full answer...

Answer 2

Yes, it will so long as your Ford key looks like one in the picture below. The Replacement Lock Cylinder for BOLT Toolbox Latch item #BLT79FR only works with Bolt tool boxes. If not you will need item #BL7022698.

view full answer...

Answer 3

I can help you find the right replacement lock cylinder for your 2007 Chevy Avalanche LT Toolbox. If your current lock cylinder can be removed from your Avalanche's toolbox then you will need the Late Model GM Key Cylinder from BOLT #BL692915.…

view full answer...

Answer 4

Thanks for the picture of the key you have! The Bolt Lock Cylinder part #BL692918 is a fit based on seeing that and knowing you have a 2002 Avalanche.

view full answer...

Answer 5

The Replacement Lock Cylinder for BOLT Toolbox Latch part #BL7023481 was designed to work with most truck tool bax locks. Those locks are very similar to the lock on the ARE caos but there is no way to guarantee. Anothe option is the Pop & Lock…

view full answer...

Answer 6

I believe you are referring to something like the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers #PAL9555 which adds a power lock to the ARE camper shell on your 2016 Ford F-250. The only other thing that you might be…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Steve, thanks for reaching out and providing all of your details! The Timbren Rear Suspension Enhancement System #TFR1504D that fits your 2014 Ford F-150 measures 8-5/8" tall so you really only need the Spacer Kit #T48AV which comes with…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement BOLT Lock Cylinder For An ARE DCU Cap On A 2016 Chevy Colorado

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching