How to Determine Replacement Boat Trailer Axle

Question

Question:

Hello, I’m looking for an axle for my 2015 Nitro Z6 boat trailer. Could you please contact me with any info you might need or products you might have? Thanks

asked by: Robert P

0

Expert Reply:

In order to choose the correct replacement axle for your trailer you will need to know the dimensions of your current axle's hub face to hub face and spring center to spring center; I have added a link below to a video which walks you through how to measure. The other thing you need to know is the weight capacity of the axle you need, which should match or exceed the GVWR of your trailer.

For example, the Trailer Idler Axle Beam # e48GR has a 2,000 lb capacity and measures 60 inches from hub face to hub face and 48 inches from spring center to spring center.

I've added a link below to our selection of axles for you to check out, or if you get back to me with that information I'd be happy to try and find something that will work for you.

expert reply by: Kyle S

0

Answer 1

The only hub we have that is associated with a 3/4 inch spindle is #AH15450ECOMP. This is an agricultural hub that takes inner bearing #LM67048 and outer bearing #LM11949. But the spindle it fits on is not straight, it is tapered, #TRU54FR. If this…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

When selecting the correct replacement axle for a utility trailer you will need to know both the hub face (wheel center) and spring center measurements. For example, if your current hub face measurement is 88" and you replace this with an axle…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

How to Determine Replacement Boat Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching