How To Measure to Confirm Fit of RV Screen Door Slider

Question

Question:

How thick is it? Needs to fit in my screen door track.

asked by: Dean V

0

Expert Reply:

In order to find the correct screen door slider you just need to measure the track width which is the distance between the two tracks top to bottom. The Screen Door Slide part # 37211185 for example is designed to fit a 12" track width. I have attached a full list of our other size and color options.

The height of the slider is about 1". If you're referring to the thickness of the plastic, this is all pretty much a standard across screen door sliders.

expert reply by: Conner L

0

Answer 1

The closest screen door slider available is the Lippert Motor Home Entry Screen Door Bubble Slider Panel - Frosted Item #LC234101. It measures 12" x 12" x 1-3/16".

view full answer...

Answer 2

If you've taken the slider out of the track and measured it and got 11.5" x 11.5" then you'd want the want to get something a bit smaller like the Replacement Slide for P-Series RV Screen Doors -11-7/8" Wide x 11-11/16"…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 6

The step motor 59734-20 will need to be replaced with the Replacement Motor for Lippert Electric Coach Step part #LC301695. If your connectors are different you could remove the connector on your current motor and install it in place of what comes…

view full answer...

Answer 7

While I am unable to find a removable plug which matches your dimensions you may be able to replace the entire assembly with the Stainless Steel Cap and Plug #LHCS108-SI60C. This cap fits a wheel with a pilot hole of 4-1/4" which is the common…

view full answer...

Answer 8

I recommend the Seaflo Diaphragm Pump for Boats and RVs #SE58FR to replace your current Shurflo 2088-422-444. The Seaflo is 12v and 45 psi just like your current Shurflo but has 3.0 gallons per minute compared to the 2.8 gallons per minute your…

view full answer...

Answer 9

The Replacement Converter #PD4655V is the correct converter for your Parallax 7355 power center. I do not see that WFCO shows their 8955PEC being acceptable to use with your Parallax 7355.

view full answer...

Answer 10

As you have a Coleman Mach system currently you can use the Furrion Chill AC units from the list below. These will simply replace only the rooftop units and the controls and thermostats you currently have in place with control the new AC's. 13.5K…

view full answer...

Answer 11

A Dexter Torflex axle that has a capacity of 1,400 lbs would be a #9 Torflex axle, and we do have the right bearing kit for that. The correct part is the Bearing Kit #BK1-150.

view full answer...

How To Measure to Confirm Fit of RV Screen Door Slider

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching