Tandem Axle Trailer Fenders For 15" Wheels With Tires 60" From Front to Rear

Question

Question:

Could you advise what size trailer fenders I should purchase for my tandem axle trailer which has axle spacing of 31 inches? From front of front tire to rear of rear trailer its about 60 inches. 15 tires. Thanks so much!

asked by: Chuck

0

Expert Reply:

You will want the Tandem Axle Teardrop Trailer Fenders # HP44VR for your trailer. These fenders are 66" long, 9" wide and designed for 14" and 15" wheels. These will give you the necessary clearance with having the tires 60" from front to back.

We do have the Backing Plate # HP82FR if you need to have one with your trailer. These are sold individually while the fenders are sold as a pair so be sure to order 2 to fit on both fenders.

expert reply by: Bud M

0

Answer 1

The Backing Plate for Tandem Axle Trailer Fender #HP82FR you mention is the correct backing plate for both the Tandem Axle Teardrop Trailer Fenders - Rounded Edges #HP94VR and the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers #HP44VR.

view full answer...

Answer 2

The Tandem Axle Teardrop Trailer Fenders part #HP44VR which are 66" long measure 9" wide. I have attached a photo below.

view full answer...

Answer 3

The Tandem Axle Trailer Fenders - Double Radius - Steel - 14" to 15" Wheels - Qty 2 #HP94VR are 65" long x 9" wide x 15" tall and they are designed to work with 33 to 35 inch on center axle spacing.

view full answer...

Answer 4

The two best trailer fender options we offer in the size you need are as follows: Tandem Axle Teardrop Trailer Fenders part #HP44VR - 66" long x 9" wide x 19-3/4" tall -Steel Tandem Axle Teardrop Trailer Fenders part #HP34VR - 65"…

view full answer...

Answer 5

The Tandem Axle Trailer Fenders #HP22FR is the closest size we have to the dimensions you have on your 1994 EZ Loader boat trailer. This fender is 60" long, 12" tall and 9" wide.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Tandem Axle Trailer Fenders For 15" Wheels With Tires 60" From Front to Rear

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching