Mounting Bolt Pattern Size For Electric Trailer Brake Kit # AKEBRK-35-SA

Question

Question:

Bolt pattern size on your parts# AKEBRK-35-SA, 10 brakes for 3500# axle Thank You

asked by: Gary A

1

Helpful Expert Reply:

The Electric Trailer Brake Kit # AKEBRK-35-SA has a square 4 bolt mounting pattern with the bolts spread 2-13/16" both vertically and horizontally. I have included an image with these measurements.

expert reply by: Bud M

1

Mounting Bolt Pattern Size For Electric Trailer Brake Kit # AKEBRK-35-SA
(click to enlarge)

Answer 1

The kit you are looking for is the part #BRKH10B which is nuts and lock washers needed to install the brake assemblies part #AKEBRK-35-SA that you referenced. The nut size is 7/16-20.

view full answer...

Answer 2

Based on what information I could find about AL-KO 8490 hub and drums, it is rated for 3,500 pound axles, has a 5 on 4-1/2 bolt pattern, and is a 10 by 2-1/4 inch drum. If this is the case, we have several options for you. I have attached a link to…

view full answer...

Answer 3

I was able to find the 126003 hub and was able to determine that it is a 3,500 lb hub/drum with a 5 on 4-1/2 inch bolt pattern just like the #AKHD-545-35-K that you referenced. This hub will work as a replacement for your Lippert.

view full answer...

Answer 4

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 5

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 6

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 7

Yes, the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-35-SA that you referenced are an exact replacement for the AxleTek assemblies you have now that have Axletek-10-GG stamped on them. If you check out the attached picture you can see the…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 10

From my research, the correct replacement for the UFP HD1377 hub/drum is the Trailer Hub and Drum Assembly part #AKHD-545-35-K or the Dexter 5 on 4-1/2 Complete Hub-and-Drum Assembly part #84546UC3. These hub/drums both use a L68149 (1.378"…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Mounting Bolt Pattern Size For Electric Trailer Brake Kit # AKEBRK-35-SA

Product Page this Question was Asked From

Continue Researching