Hitch Recommendation For 2020 Rockwood Mini Lite 2511S

Question

Question:

We have a 2020 Rockwood 2511S camper, I see that the new 2021’s have a rear hitch on them do you sell a hitch that will fit this camper? Thank You

asked by: Brad

0

Expert Reply:

Our most popular aftermarket trailer hitch for RVs is the CURT # 13703 Adjustable Width Hitch. It's a Class III frame mounted hitch that is rated for the use of hauling RV accessories (such as bike racks, bbq grills, etc).

It has an adjustable width up to 72" wide and should fit the frame of your Rockwood Mini Lite.

expert reply by: Aaron A

0

Answer 1

Yes, you could use a frame mounted adjustable trailer hitch like the Curt Adjustable Width Trailer Hitch Receiver for RVs #C13704. You'll just want to measure the distance from the inner walls of the frame beams to determine the frame width of…

view full answer...

Answer 2

You will need to do some measuring to determine if you will need an adapter with offset or not, or if you will even be able to tow a 5th wheel trailer with your gooseneck hitch. Here is how to determine if an offset would be required. First, measure…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

Hello Mike, Sounds like you are getting things set up the right way and not going over your payload, I respect that. It looks like the weights are the same whether you have a 6 3/4' or 8' bed. If you happen to have an aftermarket hitch,…

view full answer...

Answer 11

Hello Nick, The Hitch ball for the Curt #C60642 will sit above or slightly forward of the rear truck axle. I attached 2 pictures of the underbody of the 2022 GMC Sierra, as you can see that the Curt #C60642 sits in the same spot as the B&W…

view full answer...

Hitch Recommendation For 2020 Rockwood Mini Lite 2511S

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching