Is There a Pneumatic Trailer Jack Wheel Available

Question

Question:

Is there a pneumatic tire available for a swivel trailer jack which typically has the hard plastic tire?

asked by: Tom L

1

Helpful Expert Reply:

I may have a solution for you, but we don't carry any true pneumatic wheels for swiveling trailer jacks-they're typically only going to be used on heavy duty trailer jacks and dollies like the Trailer Valet # STC-V211. With that said, you may be able to use the Replacement Wheel for Brophy Heavy-Duty Cable Camper Jacks # 1206 which is a replacement for the Brophy # CX74 or # CXHD jack. This is a 2 piece wheel with a hard rubber tire, as opposed to a single piece plastic wheel that you'll find on most trailer jacks.

This replacement will work for a jack with a wheel that is 6 inches in diameter and has a 1/2 inch diameter hole. It is going to be roughly 1-1/2" wide, so you'll want to make sure that you've got sufficient width to make this work, as well.

expert reply by: Erik B

1

Answer 1

Thanks for the pictures. Everything definitely looks the same and the Bulldog #BD150415 is designed specifically for Genie basket lifts. Also, your picture that shows the label code of F3351 helps a lot becasue part #BD150415 has the same label on…

view full answer...

Answer 2

For a jack to use in an emergency to change a flat tire I recommend using the Powerbuilt Bottle Jack #ALL620471. This jack has a lift range of 11" to 21" and a 6,000 lb capacity which is more than enough for your camper trailer. I've…

view full answer...

Answer 3

It is not recommend to jack up a trailer by the axle. This may cause damage to the axle itself. It also puts too much stress on the leaf springs. Instead, you will want to place the jack under part of the trailer frame preferably next to the leaf…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Is There a Pneumatic Trailer Jack Wheel Available

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching