Replacement Atwood 88555 8,000 Lb Weld-on Trailer Coupler

Question

Question:

What weld on replacement for this 8000 lb coupler do you recomend? Atwood 88555 A frame Coupler

asked by: Herb J

0

Expert Reply:

To replace the Atwood 88555 coupler, I recommend Bulldog Heavy-Duty Cast Head Coupler w/ Wedge Latch part # BD43805W0317 which is a weld-on option rated for 8,000 lbs and takes a 2" ball.

expert reply by: Heather A

0

Answer 1

Unfortunately the Atwood coupler in your picture (appears to be part 88555) has been discontinued so there is not any latch kit or replacement parts available. At this point the only option we can offer is to replace the coupler entirely. The most…

view full answer...

Answer 2

There will be no trailer coupler latch repair kit for an Atwood Trailer Coupler 88555 which is discontinued. Unfortunately, the only option is a full replacement for which I recommend the Demco A-Frame Trailer Coupler part #DM14793-81. This coupler…

view full answer...

Answer 3

The AT15775 part that you referenced was a replacement latch repair kit from Atwood for yoke style A-frame couplers. This kit is no longer available as Atwood was bought out and their parts were discontinued. For a replacement yoke style coupler for…

view full answer...

Answer 4

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 5

For an RV with a currently installed Dometic Duo-Therm 59516.531 AC unit, I recommend the Advent Air for Dometic Setups, #ACDOM150. This is a 15,000 Btu replacement option that plugs directly into your current Dometic setup and works seamlessly with…

view full answer...

Answer 6

I recommend replacing your Atwood coupler with a Demco A-Frame Trailer Coupler #DM14791-97, as parts are virtually impossible to find for the older Atwood couplers. This will get you all new latch components that feature an EZ latch system. The…

view full answer...

Answer 7

The replacement for an Atwood P/N 88555 is the etrailer #CA-5210-B, weld on A-Frame trailer coupler featuring a yoke latch on 2" ball with 8000 pounds capacity. This has a real nice powder coat black finish that will resist rust for a long time.…

view full answer...

Answer 8

I do have an option for you but latch repair kits are coupler specific and there are very few out there. Furthermore, the Lippert 2" Latch Coupler Repair Kit 678750 is no longer available and I know this isn't what you want to hear but the…

view full answer...

Answer 9

I have a couple different options on ways to fix a loose ball mount. The Anti-Rattle Hitch Pin, #SHP2061, dramatically reduces any movement or vibration between your hitch and hollow shank ball mount. The No-Rattle Trailer Hitch Wedge, #MPG908, will…

view full answer...

Answer 10

To order the correct Solera replacement arm size, simply measure the length of the wall-mount extrusion from top to bottom. I've pointed this out using the photo you sent in as an example. Short styles will measure 61-1/2" and use part…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Atwood 88555 8,000 Lb Weld-on Trailer Coupler

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching