Replacement Vent Cover Availability for 16" x 16" Vent on 1997 Holiday Rambler Vacationer

Question

Question:

Do you have the 16” covers. My cover hinge on the side. I turn the knob and it opens up. 1997 Holiday Rambler Vacationer

asked by: Nick

0

Expert Reply:

I believe that you have a standard vent with the 14" x 14" opening as the covers tend to measure 15" x 15" completely across like the Ventline # BV0554-01. If you were measuring the base of your vent where it sits on the top of your 1997 Holiday Rambler Vacationer then that would make sense where you got the larger measurement from.

If you can send me a picture of the hinge style for your vent I can make a replacement recommendation for you out of the linked selection of replacement lids.

expert reply by: Jon G

0

click to enlarge

Answer 1

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Hello Robert, thanks for reaching out. The best option for this will be to replace your rooftop AC, controller and distribution box. Do you prefer a wall thermostat, or a distribution box with manual controls on the ceiling? We have options for both,…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Bob, none of the Torklift camper tie downs we offer fit the versions of your 2023 Ram 2500 that have the deployable step. The Happijac tie downs like the part #LC236326-205221 that fits your truck wouldn't have this problem though.

view full answer...

Answer 8

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 9

Hey there Harry, that's a good question, as the difference is the strength of the aluminum vs. polycarbonate Retrax tonneau covers that fit your 2024 Ram 3500 with a 6-1/2 foot bed. The aluminum RetraxPRO MX Hard Tonneau Cover #RT80232 has the…

view full answer...

Answer 10

Since we don't carry the PullRite line I can't really speak to their quality but from what I can see from there website their 2900 model is fairly similar to the Demco Autoslide 5th Wheel Hitch w/ Slider #DM89GV. Both hitches offer 14"…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Vent Cover Availability for 16" x 16" Vent on 1997 Holiday Rambler Vacationer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching