How Much Upward Bend Should Trailer Axle Have
Question:
How much of a bend upward should an axle have? I used a 4 foot level and centered it on the bottom of my axle. On my front I could put a 13/64 drill bit in the arch but on the rear I can put a 3/8. I ask this because the back seems a little too bowed up and has put a dent in the frame in the center.
asked by: Timothy K
Expert Reply:
While trailer axles do feature an upward bend like you are describing, there isn't a particular amount/measurement that is standard across the board. This bend in the axle is designed so that it will straighten under a trailer's loaded capacity. While I can't really say for sure if the bend you measured at the rear on your trailer is normal or not, the damage that it is causing to the frame is certainly cause for concern. This either indicates that there is indeed too much of a bend or maybe something else going on with the trailer's suspension that would have caused it to be this way. Another possibility is that the axle is over-rated for the trailer, which might result in the trailer's load not being enough to straighten out the bow.
My best recommendation would be to simply bring the trailer up to a local shop to have them take a look at all of the suspension components. It may be that the axle needs to be replaced, but I would just make sure that there isn't another underlying issue going on first so that it doesn't happen again.
I have attached a link that will take you to our available selection of trailer axles that you can look through if needed.
Product Page this Question was Asked From
Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- Idler Hubs
- 3500 lbs
- 5 on 4-1/2 Inch
- 74 Inch Spring Center
- 89 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Should Trailer Axle have Bend In it that Faces Downward
- Shop: 6-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 26" Long
- Shop: Dexter Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double-Eye Springs
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Dexter Trailer Axle w/ Electric Brakes - E-Z Lube - 5 on 4-1/2 Bolt Pattern - 95" - 3,500 lbs
- Shop: Dexter Trailer Axle w/ Electric Brakes - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 2,000-lb Axles - 7" - 5 on 4-1/2
- Q&A: Locating Replacement Dexter P-15 Axle on Trailer
- Shop: Dexter Trailer Axle Beam with E-Z Lube Spindles - 95" Long - 3,500 lbs
- Video: Tandem-Axle Trailer Hanger Kit for Double-Eye Springs Review
- Video: Complete Breakdown of the Dexter Trailer Axle Beam with E-Z Lube Spindles
- Search Results: safety cables
- Video: Comprehensive Review: Stabilizer Jacks
- Q&A: Should Trailer Axle Be Bowed Down in Middle
- Article: How to Accurately Measure Trailer Leaf Springs
- Search Results: 26 inch long trailer leaf springs
- Q&A: Can I Use Heavier Rated Leaf Springs on Trailer Without Causing Damage
- Q&A: Determining Correct MORryde CRE3000 Equalizer Kit For 2019 Heartland Fuel 352 5th Wheel Trailer
- Search Results: morryde cre3000
- Q&A: Can Heavier Leaf Springs Be Used On Tandem-Axle Boat Trailer
- Article: VCC Pickup and Dropoff
- Search Results: trailer tool box
- Video: Review of the Equa-Flex Cushioned Equalizers
- Video: A Closer Look at the Stabilizer Jack
- Search Results: valve stem
- Search Results: side mount jack
- Q&A: Does Kenda Karrier ST175/80R13 Radial Trailer Tire & Black Wheel Come Balanced
- Video: Detailed Breakdown of the Replacement U-Bolt w/Nuts for 8,000-lb, Round Trailer Axles
- Search Results: 5200 lbs axle trailer brakes
on Trailer Suspension Parts
Don L.
11/3/2021
I bought a brand new, square 1-1/2" axle: "2000-Lb. Capacity Spring Trailer Axle with Adjustable Spring Mounts — 59 1/2in. Hubface, 43in.–49in. Spring Center, 64 1/2in.L, Straight". After reading your articles, I went and looked for a bow for top or bottom, it has none. I used a straight 4' level. All 4 sides are perfectly flat, no bow on any side, whatsoever. Is this OK, or should I return it and buy a different one? Old axle was starting to sag and wear tires after 20+ years. Also, how much side to side play should I have where my springs are bolted to my trailer? Currently I have right at a 1/16" gap at all 3 bolt locations, each side. While axle is removed, I could unbolt and shim with a washer if current gap is too wide. What do you suggest?