Meaning of Error Code RC with Curt Tri-Flex Trailer Brake Controller C24VV

Question

Question:

I am pulling a trailer and my brakes seem to work properly but the box shows code RC. What does that code mean and is there a problem?

asked by: Jose G

0

Expert Reply:

I could not find purchase history for a brake controller based on your email address but I do note that you referenced a question regarding the Curt Tri-Flex # C24VV. With this brake controller the code RC indicates that the unit needs to be recalibrated.

You can accomplish this by unplugging the trailer connector from the tow vehicle, waiting a minute or two and then re-connecting it.

I linked the installation instructions and troubleshooting guide for this item for your reference.

expert reply by: Adam R

0

Answer 1

The r.C. error code on the Curt Triflex part #C24VV that you referenced means that recalibration is needed and you are supposed to unplug and replug in the brake controller. If you are seeing this error all the time I would be willing to bet you have…

view full answer...

Answer 2

Since your 2001 GMC Sierra came with a factory installed 7-way trailer connector, GM should have already completed the connections under the hood at the fuse box. However, we have found that GM did not complete the wiring on all trucks, even if they…

view full answer...

Answer 3

The minimum cross bar spread to install the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs part #TH898 is 24" apart. So the bars must be at least 24" apart for safe use. The maximum cross bar spread is 36" so it only…

view full answer...

Answer 4

The minimum crossbar spread for the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898 is 24" - meaning from one point on the front crossbar to the same point on the crossbar has to measure at least 24" for the…

view full answer...

Answer 5

The nc code on the Tekonsha Prodigy brake controller indicates that no trailer is connected. When you step on the brake pedal though it should still say that the trailer is not connected. It is possible that there is a short being caused by a dirty…

view full answer...

Answer 6

If you check out the attached instructions for the Curt TriFlex Trailer Brake Controller #C24VV you can see that the OL code you are getting means that there is an "Overloaded output circuit, trailer brake system fault". Whichever…

view full answer...

Answer 7

When the display flashes a d.C. code, it means no trailer is connected (or at least that's what it's detecting). This could be either because the trailer connection has become unplugged, there is a bad pin, a bad wire or the trailer brake…

view full answer...

Answer 8

view full answer...

Answer 9

I recommend starting by checking both the tow vehicle side and trailer side connectors. Check to make sure that they are free of any debris or corrosion, cleaning out as needed. The D.C. message you are getting on the Curt Triflex #C24VV indicates no…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Meaning of Error Code RC with Curt Tri-Flex Trailer Brake Controller C24VV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching