Wiring Diagram Recommendation for 4-Way Round Trailer Connector

Question

Question:

My towing cable wires colors are green, red, brown and yellow, can you show or explain the way to connect it to connector

asked by: Sol

0

Expert Reply:

Looks like you have a round 4-way connector in the picture you submitted. The colors you mentioned aren't totally a match for standard colors but they are close. Normally the colors are:

White - Ground Return
Green - Right Turn and Brake Lights
Yellow/Red - Left Turn and Brake Lights
Brown - Tail Lights

You'll need to wire by function instead of color since yours aren't a total match.

I have attached a photo that shows typical wiring for a 4-way round connector.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For a 2022 Chevrolet Colorado you only flat tow four-wheel-drive vehicles that have an N (Neutral) and a Four-Wheel Drive Low (4 (n) setting. Look for knob on the dashboard. This will most likely be the last position on the right of the knob and be…

view full answer...

Answer 2

When looking at the front of the socket of the #BLU63XR, wire the 4-way round socket as follows - Top Left - Left stop/turn, yellow wire Top Right - Right stop/turn, green wire Bottom Left - Ground, white wire Bottom Right - Tail Lights, brown wire I…

view full answer...

Answer 3

Hey Geroge, We actually do have a hitch fit for your 2026 Chevy Equinox EV! Right now, the only one that fits is the Curt Class III #C89RV, but even at that it's still a great hitch receiver that can resist the elements and remain strong for a…

view full answer...

Answer 4

Yes, the the Roadmaster Tail Light Wiring Kit with Bulbs, #RM-155 can be used with the Brake Buddy Classic 3, #HM39494. We actually have an install video created for the Brake Buddy Classic 3, #HM39494, see link below. This is located on the product…

view full answer...

Answer 5

One end of the umbilical cord that comes with the Brake Buddy Stealth Supplemental Braking System part #HM39530 is a 7-blade round connection that connects to motor home's 7-way plug. The other end is a 7-flat connector that plugs into the…

view full answer...

Answer 6

The Brake Buddy Classic 3 Portable Supplemental Braking System, #HM39494 comes with the BrakeBuddy Towed Vehicle Battery Charge Kit, #BB54FR. This should be used when installing the Supplemental Braking System, #HM39494. There's good chance the…

view full answer...

Answer 7

Yes, we do have trailer hitch options for a 2003 Ford E350 Short Bus. That said, these require drilling and or welding. There are no bolt-on options for this application. I recommend the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver part…

view full answer...

Answer 8

The Curt hitch part #14055 will fit the cutaway models of the 2003 Ford E-350 if the bolt holes on the frame of the van are 38-1/4 inches apart on center. I attached an install video for you to check out as well.

view full answer...

Answer 9

Most of the time the 4-Way connector is wired as follows. Looking at the front of the socket on the vehicle side with the cover raised the top left pole is the yellow, left turn/brake pole, the top right pole is the right turn/brake pole, the bottom…

view full answer...

Answer 10

What I would do is try bypassing the tee connection on the Curt T-Connector #C56413. If you plug everything back up how it was before you installed this kit then you can test the 7-Way at the back of your 2018 Ford F-150 to see if everything is…

view full answer...

Answer 11

The replacement hinge seal you need for your Extang Encore tonneau cover is the Replacement Hinge Seal for Extang Encore Tonneau Covers - Qty 1 #EX32620464. Each of these come with a replacement of 1 seal. I went ahead and attached a video that shows…

view full answer...

Answer 12

Hey Doug, yes the Replacement Hinge Seal part #EX32620464 is the correct hinge seal for your Extang Encore Tonno cover.

view full answer...

Wiring Diagram Recommendation for 4-Way Round Trailer Connector

Product Page this Question was Asked From

Continue Researching