To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Mitsubishi Outlander with this custom harness. Connectors plug directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's factory tow package wiring harness. The connection point for the 4-way harness is located behind the passenger's-side interior trim panel in your rear cargo area. The power wire plugs into the factory wiring harness in your engine compartment, on the driver's side. Once you've plugged this in, route the other end of the harness to your car battery and connect it to the positive terminal.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (24 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. Connectors plug directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.The price is reasonable, the piece fit perfectly. I'm not very skilled in installing things like that and it was incredibly easy and simple (just took a couple of minutes!). Watched the video and arranging the cables was a piece of cake. It was a very fast shipping and I'm very happy with the finished product and service. I will recommend it in the future.
Great products and great direction the videos made it so easy to install even with a hick up I still got everything in time
Easy install, my 2011 outlander SE was pre-wired and I just had to hook it all up. I only tow a light ATV a few times a year so this solution is perfect.
This kit was super easy to install. Could be done in half an hour but I am anal about electrical stuff so it took me a bit less than an hour. I took my battery out to get to the connector easier but it could be reached by leaving the battery in. This is the kit you need. Fits the stock connectors perfectly and can be rolled up to fit in the jack storage area.
Jeff T.
5/8/2014
How do I know if my 2008 is tow ready for the intalation of this particular kit? I only ask this from the last comment response to the 2010 instalation. Thanks!
The product arrived in excellent shape and was easy to install. The only comment was that no drilling was necessary on the 2012 Outlander, there is a factory supplied pre-drilled and taped hole over the right wheel well. Just put in the metric bolt and your done in the rear. The front hook up was easy once you find the plug which is taped to a wiring harness behind the left headlight.
Wiring harness for the quick and easy installation. The online installation videos that are available are very helpful.
The Hitch fit great. Hardest part was I had to re-tap the rusted weld nuts..
The wiring harness was easy also..I had to remove battery to get at plug in..
Thanks...
Wanted to set up my '09 Mitsubishi Outlander for pulling our boat trailer - this kit came with everything needed and was extremely quick and easy to install.
The price is reasonable, the piece fit perfectly. I'm not very skilled in installing things like that and it was incredibly easy and simple (just took a couple of minutes!). Watched the video and arranging the cables was a piece of cake. It was a very fast shipping and I'm very happy with the finished product and service. I will recommend it in the future.
Super fast and easy installation. I think I spent more time with securing the ground into the sheet metal than I did actually installing the whole kit.
This harness kit was so easy to install that it took me only 10 minutes. It's simplicity saved me hundreds in labour costs. A+
Product was as expected. All the clips fit the OEM harness and install was very simple. It's been a year and I have had no issues.
perfect fit tonpre-existing connectors. 10 minute job! Will recommend to a friend
Very easy to install I just followed the instructions and it’s working great
Very easy to install, directions were easy to understand
Eli
2/27/2020
Harness still works just fine and I haven’t had any issues. It’s stored inside the car when not used so that’s helpful.
Super fast delivery and great customer service .
Just want I wanted.
Easy to install .
Fit to perfection easy to install
Super fast shipping and free.
Easy too hook up
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Larbi
6/10/2013
Hello, does this T-connector works with LED taillights mitsubishi outlander 2010 or i need other wiring to avois short circuit added to this connector ?Thanks