To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs into OEM tow package wiring harness. Powered converter reduces strain on wiring system. SMT construction ensures superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's factory tow package wiring harness, which is located behind the rear bumper, on the driver's side. Once you've plugged in the T-connector, insert the included 10-amp fuse into the integrated fuse holder.
Once installation is complete, the 4-way connector will be stowed beneath your vehicle, near the trailer hitch. A mounting bracket (sold separately) is recommended to keep the connector secure.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.7 out of 5 stars (46 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs into OEM tow package wiring harness. Powered converter reduces strain on wiring system. SMT construction ensures superior performance.Couldn't be happier! Super quick shipping. Good price and clear instructions.
Only hard part was my existing frame nuts were a bit rusty and dirty and it made threading the bolts slightly difficult.
The small connector with the 2 wires will not connect and clip to lock it. Way to tight need a difference connection.
I buy all of my trailer and towing needs from etrailer. Fast and accurate service and competitive prices. They have never failed to complete my purchases. A Big Thank You to all of the folks at etrailer!
Worked great
Ken
8/25/2023
Still working great . Thanks
Worked as advertised!
Tom
8/16/2023
One year later this harness is working like a charm.
this product fit perfectly as it said
Hitch came in 3 days thru 3 states. All parts there and in good condition.
Works great on my 2011 Santa Fe with the OEM tow package.
Couple notes:
1. One of the factory connectors (on the car side) had an orange gasket in the connector. This prevented the connector from seating properly and locking in place. I couldn't see a reason for the gasket, so I removed it (with needle nose pliers), and it worked great.
2. The cable from the box to the 4-flat connector is really short. The only good place I could find to mount the box, left the cable too short to reach the hitch receiver. I zip tied it to the hitch bar 10" or so away from the receiver, and it works fine, but is a bit inconvenient to get to.
Direct plug and play for my 2011 Hyundai Santa Fe Limited. I made a mounting tab for the plug on the hitch receiver to keep it tucked away and clean looking.
Fast and easy product was exactly as li sted
The Santa Fe 2010 Limited is prewired for a wire harness. There are two capped male plugs under and behind the bumper on the driver's side. They are very accessible. When you remove the caps there is a rubber seal or grommet inside. They should come out and stay inside the cap. If the grommet stays inside the male plug it will block the plugs from sliding together completely. Once the harness is plugged in it is easy to route inside the bumper. I stuck the converter to the inside of the bumper using the double stick patch. It is pretty clean there and seems secure.
Hope this trailer light wiring Harness lasts longer then the previous one purchased from etrailer. On the good note hooked up this harness took less then 5 minutes start to finish everything work Great, Thanks
Good product. My vehicle was pre-wired to accept this wiring harness. It was very easy to install, took me about 15 minutes. Instructions were very easy to follow.
Fits a 2007 Hyundai Santa Fe perfectly. Trouble free installation. Make sure to get a connector mounting bracket, it doesn't come with the wiring set.
Worked as described, no issues
Easy installation, price . Product arrived fast and undamaged packaged was the reason it arrived undamaged buy it
Easy install, works great
Having worked 20 years in the Military providing customer service, 15 years in a Half Billion dollar Corporation providing customer service to our valued customers, which centered around Fortune 500 members/corporations, and 5 years with the Department of Human Services - I know what EXCELLENT customer service is, and that is what you provided to me, as your customer. I STRONGLY recommend you to ANYONE seeking products you sell!!! Item I ordered arrived VERY QUICKLY,on time and was as presented on your web site. WELL DONE!!!!
I would absolutely order any accessories from etrailer.com, because of their professionalism and helpfulness with any of my inquiries.
Ordered 5/13 Arrived 5/18 Installed 5/19 Prompt service, well built, clear instructions and fits perfectly. I couldn't ask for more. I will recommend etrailer to my friends.
Very good quality product. Easy to install and all the wiring connections are sealed well to protect from corrosion and debris.
Nathaniel
2/18/2019
Product is working like brand new after a year of use in all types of Ohio weather.
This is a great product and with the videos on how to install that etrailer has, made it easy to install.
Great Harness. Easy to install. Thank you for all the help Paula.
I always find what I need at etrailer
As ordered
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
10/2/2023
I wanted to make sure that your 2010 Hyundai Santa Fe has the factory tow package? Would you be able to send a picture of the connector that you are seeing?