Tube Step Specs:
Features:
...Custom-fit, cab-length, round nerf bars help you to safely enter and exit your vehicle Raised, wide step pads ensure confident footing Slip-resistant, textured surface provides excellent...
Installation Notes:
No drilling required for installation
Product designed for vehicles without a factory rocker bar
More Information >Tube Step Specs:
Features:
...Custom-fit, cab-length, round nerf bars help you to safely enter and exit your vehicle Raised, wide step pads ensure confident footing Slip-resistant, textured surface provides excellent...
Installation Notes:
No drilling required for installation
Product designed for vehicles without a factory rocker bar
More Information >Tube Step Specs:
Features:
...diameter: 3" Step pad width: 3" Step pad quantity: 2 per bar Quantity: 2 nerf bars Lifetime warranty The step pad areas in Westin's E-Series round nerf bars are indented inste...
Installation Notes:
No drilling required for installation
Tube steps are installed by attaching mounting brackets to the vehicle frame
More Information >Tube Step Specs:
Features:
...powder coated steel is long-lasting and rust resistant Quick and easy bolt-on installation No drilling required Powder coated mild steel brackets and hardware included Specs: Tubing diameter: 3" ...
Installation Notes:
No drilling required for installation
Tube steps are installed by attaching mounting brackets to the vehicle frame
More Information >Videos
for Nerf Bars - Running Boards
Help Articles
for Nerf Bars - Running Boards
Expert Answers
for Nerf Bars - Running Boards
The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...The number you provided,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...It sounds like the 2022 Chevy Silverado 3500 you are getting has the short bed. In that case, yes, you definitely want the sliding 5th wheel hitch for clearance. The good news is you will not need to purchase the entire…
view full answer...Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies…
view full answer...A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
view full answer...Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR.…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be…
view full answer...Filter Products (8)
Contact and Help
What our customers are saying:
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Robert
Bloomington, IL