Tailgate Locks Specs:
Features:
Don't let thieves steal your cargo or tailgate. Protect your payload with a keyed, custom tailgate lock that installs under your vehicle's OEM handle, adding security for your valuables. Perfect for use with tonneau covers and camper shells.
Installation Notes:
Crew Cab models with an 8 ft bed will also need to purchase an extension harness, part number PL9510 ; sold separately
More Information >Tailgate Locks Specs:
Features:
Don't let thieves steal your cargo or tailgate. Protect your payload with a keyed, custom tailgate lock that installs under your vehicle's OEM handle, adding security for your valuables. Perfect for use with tonneau covers and camper shells.
More Information >Videos
for Tailgate Locks
Help Articles
for Tailgate Locks
Expert Answers
for Tailgate Locks
Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.
view full answer...I checked with Pop & Lock for you and there is a system that they have confirmed will work with 2011 and newer Leer 100XL, Leer 100XQ, and Leer 700: - Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau…
view full answer...The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade…
view full answer...The Bauer Products T-Handle Lock for Truck Caps #BA57VR comes with a J-327 key. So by ordering 3 of these they are all keyed alike. This particular handle is for locks rotating counterclockwise. We also have the Clockwise T-Handle #BA84VR if your…
view full answer...The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you referenced on your 2017 Ford F-250 Crew Cab Short Bed. This will give you a clean look along with the…
view full answer...Most A-Frame Trailer Couplers have a standard of 50 degrees. I produced a short video for you showing the angle of the etrailer A-Frame Coupler, part #CA5400. I have also linked an FAQ on trailer couplers.
view full answer...The standard a-frame coupler degree is 50 degrees but we do have a 32 degree coupler with the part #DM15633-81 but the rear width of it is 9-7/16 inches.
view full answer...I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…
view full answer...Pop and Lock does have the manual locking tailgate handle, #PAL5500, that will work with your 2015 Toyota Tacoma with backup camera. You can turn it into a power locking handle by adding conversion kit #PAL8525.
view full answer...I do have an option for you to get the locks working again but we don't carry Load Lock so I don't have any advice or replacement parts for this. That said, you should be able to pretty easily replace this with the Pop & Lock…
view full answer...I can certainly point you in the right direction. The Dometic Duo Therm 3107541.009 is a model that we see fairly frequently. Now I do not have literature on your specific camper that will tell me if it is ducted or ductless, but the Advent units…
view full answer...We had a customer who was able to replace his Dexter 8-155 hubs with the #8-201-5UC3-EZ that you referenced so they should work well for you. You can verify that this hub will work for you by pulling your current hub and making sure they have inner…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN