Anti-Sway Bars Specs:
Features:
Minimize sway and improve the driveability of your truck. Solid, 3/4" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. For 0" to 2" lifts. Drilling required.
Installation Notes:
Drilling is required for installation
Product is designed for vehicles at the stock height or have been lifted up to 2"
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and driver fatigue by improving the stability and driveability of your truck. Solid, 1-3/8" chromoly sway bar provides improved handling, comfort, and safety. Uses existing end links.
Installation Notes:
No drilling required for installation
This replaces the factory sway bar and will reuse the factory end links
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and improve the driveability of your truck. Solid, 3/4" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. For 4" to 6" lifts. Drilling required.
Installation Notes:
Drilling is required for installation
Product is designed for vehicles that have been lifted 2" to 4"
More Information >Videos
for Anti-Sway Bars
Help Articles
for Anti-Sway Bars
Expert Answers
for Anti-Sway Bars
The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…
view full answer...Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.
view full answer...When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack…
view full answer...I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…
view full answer...Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…
view full answer...The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…
view full answer...Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…
view full answer...The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…
view full answer...In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…
view full answer...The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…
view full answer...Filter Products (6)
Contact and Help
What our customers are saying:
Excellent service and communication. Expect part to be excellent too!
Tommy
Tifton, GA