Features:
Strengthen the factory tailgate on your Jeep and carry an oversized spare tire. The frame and heavy-duty tailgate hinges reinforce the tailgate to support extra weight. Spare tire mount works with tires up to 40" in diameter.
More Information >Jeep Spare Tire Carrier Specs:
Features:
This heavy-duty spare tire mount upgrades your Jeep's factory carrier, allowing you to carry an oversized spare. Works with tires up to 40" in diameter. Adjusts to keep your third brake light visible.
More Information >Features:
Strengthen your factory tailgate on your Jeep to handle an oversized spare tire. Frame reinforces the tailgate to support extra weight. Works with factory and aftermarket spare tire carriers. Requires MORryde heavy-duty tailgate hinges to install.
More Information >Videos
for Jeep Spare Tire Carrier
Help Articles
for Jeep Spare Tire Carrier
Expert Answers
for Jeep Spare Tire Carrier
Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…
view full answer...You are correct that the Jeep bracket should have been reinstalled when installing the Blue Ox Base Plate #BX1139. I have linked another video near the bottom of the page where you can see the brackets being reinstalled on a 2020 Jeep Wrangler…
view full answer...Yep, you're 100 percent on the money, Al. The 200 lb tongue weight capacity is only for what is put in the receiver and does NOT count the weight of the spare tire and the carrier itself for the Roadmaster Spare Tire Carrier #RM-195125.
view full answer...The Lippert Flow Max RV Toilet #LC67AF requires a minimum of 12" for the rough-in.
view full answer...Yes, the Roadmaster Spare Tire Carrier #RM-195125 can pivot to the left or right depending on what kind off clearance you have. We only show to the left in the video because there is a ladder on the right side, but if you check out the attached photo…
view full answer...Yes, the Roadmaster Spare Tire Carrier #RM-195125 will work on your Jayco Melbourne motorhome, and it is straight out so it won't lower where the factory receiver is. Keep in mind the receiver on the spare tire carrier is for accessories or flat…
view full answer...We do have some replacement wheels that you can see with parts #AM20783, #LHHA420, and #TA56FR if you're only needing the wheel. Since this is on a motorhome you're actually going to need to look into regular vehicle tires if you need a tire…
view full answer...There are two possible options for you. The Dexstar Dual Wheel #AM20790 which is the 16" x 6" size you need with the 8 on 6-1/2" bolt pattern, uses flange nuts instead of standard lug nuts, and would work with the 225/75R16 tire you…
view full answer...It depends on what 5th wheel landing gear you have. For example; the Lippert Landing Gear part #LC333966 is rated for 6,000 lbs. It can be used with a trailer that weighs more than 6,000 lbs because it is only supporting part of that load - the…
view full answer...For the 6-point Level-Up System by Lippert, I made a call to the manufacturer to ensure you would receive correct information. Lippert said that when you bolt the footpads to the jacks, you need to torque them to 132 ft-lb. They said to make sure to…
view full answer...In order to add a 7 way connector on you 2020 Jeep Wrangler JL you'll need to start by adding a 4 way trailer connector like the Tekonsha #118786, which gives you the connections needed to install a 7 way connector. Once you've installed the…
view full answer...I went out to our warehouse and measured an outer bore diameter of 2-1/4 inches on the etrailer.com Trailer Idler Hub Assembly #AKIHUB-545-2-G-2K that you referenced. The reason we don't typically list this dimension on our trailer hubs is…
view full answer...Filter Products (6)
Contact and Help
What our customers are saying:
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN