Truck Bed Slide Specs:
Features:
Slide-out truck bed tray lets you get gear without climbing or crawling. Steel-framed, laminated plywood deck extends smoothly - up to 75 percent of its length - on sealed bearings. Aluminum sides have built-in tie-down tracks. 1,000 Lbs capacity.
More Information >Truck Bed Slide Specs:
Features:
Slide-out truck bed tray lets you get gear without climbing or crawling. Steel-framed, laminated plywood deck extends smoothly - up to 75 percent of its length - on sealed bearings. Aluminum sides have built-in tie-down tracks. 1,500 Lbs capacity.
More Information >Videos
for Truck Bed Slide
Help Articles
for Truck Bed Slide
Expert Answers
for Truck Bed Slide
My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part #20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present…
view full answer...On a single axle trailer you will want to have a hanger spacing of around 22-3/4 inches when using the 23-1/8 inch long Double-Eye Spring #e59SR. This will allow that rear shackle to correctly lean away from the axle for proper suspension travel.
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the…
view full answer...On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…
view full answer...For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure 12" x 2", bolts onto a 5 bolt mounting flange,…
view full answer...The Truck Trolley Sliding Truck Bed Tray #TR87VR actually just installs using straps, which is why it has a 300 lb weight rating as opposed to 1,000 + lbs like we see with some of the sliding cargo trays that bolt to the truck bed. The installation…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast you're traveling, and also driving habits. So…
view full answer...I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I…
view full answer...The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…
view full answer...We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…
view full answer...You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the…
view full answer...