Optimize your trailer's storage by creating a shelf with this e track wood beam socket. Supports one end of a standard 2x4 board. 500-lb Load limit.Features: Create a shelf for extra storage in your trailer Just snap into an e track anchor and slide in a board Add another socket to hold opposite end of board in place Works with a standard 2x4 board (not included) Pre-drilled with holes in sides to secure wood with screws (not included) Attaches to e track easily with spring fitting Specs: Quantity: 1 socket bracket Overall dimensions: 3-3/8" long x 1-11/16" wide Safe working load limit (WLL): 500 lbs 1-Year limited warranty
When you pull your trailer down a gravel road or pull out after a full day at the lake, this rear hanger will support every mile. It holds your 2" slipper spring, so bumps and potholes dont get the best of your cargo.Specs Application: Rear hanger for slipper spring suspension Fits 2" wide slipper springs General: Overall dimensions: 1" long x 1-1/4" tall x2-1/2" wide Inner width: 2-1/8"
Keep your Dexter 10K slipper suspension tight with this 3/4" x4-1/2" spring eye bolt. Sized for rubber bushed 10K general duty springs, it installs with the 6-113 locknut and HAP-258-03 equalizer kit.
These flexible straps move the anchor points 6" away from your E track, making it easier to reach the D-rings. They also allow your ratchet straps to maintain a snug fit on a box or mattress without crushing the edges. 4,000 lbs Max load.Features: Flexible straps create anchor points 6" away from your E track so the D-rings are easier to reach Also help prevent box or mattress edges from getting crushed by ratchet straps Spring-loaded fittings lets you easily move straps from one E track slot to another High-visibility polyester webbing is strong and won't stretch or tear Zinc-plated steel D-rings and fittings are rust resistant Specs: Application: horizontal and vertical E track and X track Dimensions: 6" long x2" wide D-ring dimensions: 1-1/2" long x2" wide Safe working load limit (WLL): 1,333 lbs each Maximum load (break strength): 4,000 lbs each Quantity: 2 D-ring straps 1-Year warranty Note: Tie-down straps and their accessories must be chosen according to their safe working load limit (WLL).
This flexible strap moves the anchor point 6" away from your E track, making it easier to reach the D-ring. It also allows your ratchet strap to maintain a snug fit on a box or mattress without crushing the edge. 4,000 lbs Max load.Features: Flexible strap creates an anchor point 6" away from your E track so the D-ring is easier to reach Also helps prevent a box or mattress edge from getting crushed by a ratchet strap Spring fitting can be easily moved from one E track slot to another High-visibility polyester webbing is strong and won't stretch or tear Zinc-plated steel D-ring and fitting are rust resistant Specs: Application: horizontal and vertical E track and X track Dimensions: 6" long x2" wide D-ring dimensions: 1-1/2" long x2" wide Safe working load limit (WLL): 1,333 lbs Maximum load (break strength): 4,000 lbs Quantity: 1 D-ring strap 1-Year warranty Note: Tie-down straps and their accessories must be chosen according to their safe working load limit (WLL).
Create a tie-down point for securing a cargo strap, rope, net, or tarp by snapping this fitting into your E-track anchor or rail. Steel attachment point and polyester strap are durable.Features: Creates a tie-down point in your trailer for rope, cargo straps, net, or tarps Clips easily into an E track anchor or rail (sold separately) Constructed of durable steel and polyester webbing Specs: Strap dimensions: 6" long x2" wide D-ring dimensions: 2" wide x 1-1/2" tall Maximum load (break strength): 3,500 lbs Safe working load limit (WLL): 1,200 lbs Note: Tie-down anchors must be chosen according to their safe working load limit (WLL).
These brackets let you create a shelf on the E track or X track in your enclosed trailer or workshop. Use included screws to secure a 12" wide board to the brackets. ... Features: Brackets let you create a shelf in your garage or workshop Requires board (not included) up to 12" wide Spring-loaded fittings connect to both X track and E track anchoring systems Brackets can be easily moved from one E track or X track slot to another Included screws allow you to secure board to brackets Drill screws up through mounting bracket holes into bottom of board Heavy-duty steel construction with yellow zinc finish is corrosion resistant Specs: Quantity: 2brackets Dimensions (each): 8-1/8" deep x4-1/4" tall Distance between mounting bracket holes (center to center): 1-5/16" Weight capacity: 1,000 lbs Weight (each): 4.5 lbs 1-Year limited warranty
These brackets let you create a folding shelf on the wall-mounted E track or X track in your enclosed trailer. Included screws secure a 12" wide board to the brackets. ... Features: Brackets let you create a shelf in your enclosed trailer or workshop Requires board (not included) up to 12" wide Folding design - remove pins and fold the shelf down to save space Reduces catch hazard in high-traffic areas Easy installation - just snap spring-loaded fitting into E track or X track anchor points Brackets can be easily moved from one E track or X track slot to another Included screws let you secure board to mounting brackets Drill screws up through mounting bracket holes into bottom of board Heavy-duty steel construction with yellow zinc finish is corrosion resistant Specs: Quantity: 2bracketsBracket dimensions (each): 8-1/8" long x4-1/4" tall Distance between mounting bracket holes (center to center): 1-5/16" Weight capacity: 100 lbs Weight (each): 4.5 lbs 1-Year limited warranty
Get more ground clearance and a smoother ride. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, drop spindle lowers deck height for easy loading. Fits any trailer frame width. Includes inner (L68149) and outer (L44649) bearings.If your trailer frame doesn't have a crossmember in place, you can retrofit it with one, or you can add a support by running a piece of 2" x2" steel tubing through the square holes cut into these units. You could also add a steel reinforcement bracket to the inside of the trailer frame.
These gunwale brackets let you carry 1 canoe, hull side up, on your roof rack. It mounts to most crossbar styles, and it includes heavy-duty straps and bow/stern tie-downs to secure your canoe to the roof rack on your vehicle.Features: Gunwale bracket carrier lets you transport 1 canoe, hull side up, on your roof rack Also great for carrying a ladder Padded brackets securely hold your canoe by its gunwales and protect it from scratches and scuffs Tie-down straps and bow/stern tie-downs secure your canoe to your roof rack and your vehicle Anchor kit (sold separately) creates temporary mounting points for bow/stern tie-downs Quick and easy clamp on installation on most crossbars - no tools required Made in the USA Specs: Application: round, square, aero, elliptical, and most factory crossbars Carrying capacity: 1 canoe Weight capacity: 90 lbs Dimensions: 5-1/4" long x 5-1/2" wide x4-1/4" tall Strap length (each): Load straps: 15' Bow/stern tie-downs: 11' Carrier weight: 6.5 lbs Limited lifetime warranty Gunwale Bracket Canoe Carrier The Malone BigFoot Pro holds your canoe hull side up on your roof rack crossbars.
This hanger bracket secures the eye end of a slipper spring on your aluminum or steel trailer's suspension. It is constructed of corrosion-resistant galvanized steel and accepts a 9/16" shackle bolt.Features: Heavy-duty bracket connects the eye of a slipper spring to your trailer Bolt-on installation Attaches to the underside of trailer frame Does not include mounting hardware 7-Gauge, galvanized steel construction is sturdy and resists corrosion Made in USA Specs: Application: front of slipper spring Overall dimensions: 4-1/4" long x2-1/4" wide x2-1/4" tall Inside width: 1-7/8" Diameter of shackle bolt holes (each): 9/16" Quantity: 1 bracket Install a new suspension without the hassle of welding a hanger to the bottom of your trailer.
Every time you head to the ramp or hit the road, you count on your trailer to keep your boat or gear riding safe. This galvanized bracket connects your slipper spring to the frame, resists rust from rain, spray, and muddy drives.Easy Bolt-On Install: Mounts to the underside of your trailer - no welding required. Rust-Resistant Build: Galvanized, 4-gauge steel resists corrosion, so it's ideal for boat trailers. Made in the USA Specs Application: Front hanger for slipper spring suspension (eye end) Bolt-on installation (mounting hardware not included) Attaches to underside of trailer frame General: Overall dimensions: 5-3/8" long x2-3/8" wide x2-1/4" tall Inside width: 1-15/16" Shackle bolt hole diameter: 9/16" (each) Material: 4-gauge galvanized steel Quantity: 1 bracket Made in the USA
This hanger bracket secures the slipper end of a slipper spring on your trailer's suspension. It is constructed of corrosion-resistant galvanized steel.Features: Heavy-duty bracket connects the slipper end of a slipper spring to your trailer Bolt-on installation Attaches to the underside of trailer frame Does not include mounting hardware 7-Gauge, galvanized steel construction is sturdy and resists corrosion Made in the USA Specs: Application: rear of slipper spring Overall dimensions: 4-1/4" long x2-1/4" wide x 1-3/4" tall Inside width: 1-7/8" Quantity: 1 bracket Install a new suspension without the hassle of welding a hanger to the bottom of your trailer.
Marine-grade hub is designed for trailer idler axles. Fits 3.5K Dexter E-Z Lube and etrailer Easy Grease axles with #84 spindles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and nuts included.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Hub is designed for use on trailer idler axles. Fits 3.5K E-Z Lube and etrailer Easy Grease axles with #84 spindles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 3.5K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Install this hub-and-drum assembly on your trailer. Compatible with electric or hydraulic brakes. Fits 3,500-lb axles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Hub is made for use on trailer idler axles. Fits 2K E-Z Lube and Easy Grease axles with BT8 spindles. Inner bearing (L44643) and race, outer bearing (L44643) and race, grease seal, grease cap, and lug nuts included. Fits 13" to 15" wheels.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Marine-grade hub is designed for trailer idler axles. Fits 2K Dexter E-Z Lube and etrailer Easy Grease axles with BT8 spindles. Inner bearing (L44643) and race, outer bearing (L44643) and race, grease seal, grease cap, and nuts included.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Install this hub-and-drum assembly on your trailer. Fits 5,200-lb to 7,000-lb E-Z Lube axles. Inner bearing (25580) and race, outer bearing (14125A) and race, grease seal, grease cap, wheel bolts, and lug nuts included.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Pre-greased, marine-grade hub is built for trailer idler axles. Fits 3.5K axles with #84 spindles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, cap, lug nuts, and cotter pin included. For 13" to 15" wheels.If D = 2-5/8", then the bolt pattern is 5 on 4-1/2" If D = 2-3/4", then the bolt pattern is 5 on 4-3/4" If D = 3", then the bolt pattern is 5 on 5" If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
Replaces (1) 9/16" x 3-3/8" wet shoulder bolt for your MORryde suspension upgrade kit. Works for MORryde Correct Track, MORryde LRE, and MORryde RE suspension systems.
Filters
