Ford  x   >   Explorer  x   >   2010  x   >   F-350  x   >  

I have a Thule 450 rack with square cross bars on my 2010 Ford Explorer. I’d like to get a wind fairing to cut down on the noise from the rack. Do you know what size or kit would work? Thanks | On your 2010 Ford Explorer Thule specifies 50-inch...

Since the car has power brakes, does the motor have to be running when towing? | No, the vehicle motor will not need to be running while towing the vehicle in order for the brakes to work. When checking the owners manual for an Explorer, I...

The specs have different rating when using weight distribution. What does that mean? Is weight distribution automatic with this hitch? | Weight distribution systems are designed to help distribute the tongue weight of the trailer to the front...

Which Roof Mount Ski and Snowboard Racks Fit a 2010 Ford Explorer with Factory Crossbars, and can they be used to transport fishing rods? | There are several ski/snowboard carriers that will fit the factory roof rack on your 2010 Ford Explorer. From...

Hi, I want to install my tekonsha prodigy brake controller to my ford explorer. I have the correct wire harness that attaches the controller to the ford factory harness, however, there is no power. Thank you for your help. | The fuse for the...

hello, looking for a Drawtite bolt kit # 75437F. Do you sell these ? | To order replacement hardware for the Draw Tite hitch part # 75437 what you need is the part # RHK. On the product page of this part number you'll enter the part # 75437...

My husband passed away in January. We always loaded our bikes as a team. I am not able to load my bike by myself. I have a 2-bike Thule rack, but I need a 1-bike rack that has a lift or ramp that will assist me in getting my heavy Giant brand...

I just purchased a camper, and the dealer did not have a footplate that would fit because of the indent on the stand itself. Can you tell me if it will fit this particular jack? It seems to have the same indent, Im just not sure if it will...

We need a 8 inch drop to pull a utility trailer. Can we use an adaptor without decreasing tongue weight we can tow? | I have a couple of different options for you to use with your 2010 Ford Explorer that will give you the 8 inch drop that...

We have a GCH 6 Atwood. We would like to replace it with the same features. Ours has a heat exchanger on the back. Could you tell us the part number? 6 gallon, DSI, propane and 120v. | The Dometic RV Water Heater part # DMC74FR would be...

2010 Ford Explorer Eddie Bauer Edition Factory Tow Circuit Problem - The trailer connector on the back of the vehicle has a 7 pin and 4 pin connector. Both connector outputs work except for the Right Turn/Brake output. That tells me its not...

With #31545 Curt front mount trailer hitch receiver will I have to trim any bumper parts on my 2010 explorer xlt ? Thanks | There is no drilling, cutting or modifying of any of the parts on your 2010 Ford Explorer XLT for installation of the...

Will this hitch carrier #c18145 work well on a 2010 Ford Explorer? | To determine if the Curt 20x48 Cargo Carrier will work with your Explorer, you will need determine if there is enough clearance at the rear of the vehicle. You will need to...

My ladder now is about 105 inches long, do have any that long for a George of 2000. | The longest ladder that we have is the 99-1/2" ladder from Stromberg Carlson. This comes in Silver # LA-401 as well as Black # LA-401BA and has a customizable...

In the video he mentions a tire size of 205 75r 15 , but that size is not listed , so will this work on 205 75r 15 ?? | Hey there Robert, thanks for the question and even though it is not listed, a 205/75-15 tire is absolutely compatible with...

2010 Ford Explorer Mine is a four door model with the large spare tire and class 2 hitch all ready made on the frame will the Curt part # 13112 fit on corectly with the full size spare tire. and if not what hitch will ? | Yes, the Curt Class...

I need a ball mount, six inch , at least 700lbs tongue weight, at least 7500lbs towing weight, 2inch ball. Would prefer a ball mount that has the ball pre-torqued onto the ball mount if at all possible. Can you make some recommendations for...

Where do I find the wiring to connect my control unit to? I have a factory installed type III/IV towing package on my truck. Will it be located under the dash? How do I recognize it....special color or configuration? 2010 ford explorer...

Which oil coolers will fit on a 2013 Ford Explorer with a 3.5 liter engine? | I did some checking and it looks like the oil filter threads on your 2013 Ford Explorer with a 3.5 liter engine are M22x1.5 mm, so you are going to need an oil cooler...

Is this kit compatible with Aries Grille Guard model 3059 black or 3059-2 polished? | The Aries Grille Guard # AA3059 does fit your 2010 Ford Explorer and the appropriate Replacement Bracket and Hardware Kit is part # AABRKT-3059. Aries Replacement...

My 2010 Ford Explorer has very limited space and the lock must have a side entry for the 5/8inch pin because there is no room to a key into the end of the most common locks. I purchased a side load lock, but there is a bolt head behind the...

Trying to find the cold wire for brake switch on 2010 ford explorer. Had to hard wire brake controller | For a 2010 Ford Explorer the cold brake light switch wire should be a purple and white wire. You will want to test it to make sure with...

What mirror is the best fix for a 2010 Ford explorer xlt | I would be happy to find some towing mirrors that clip onto your factory mirrors but if you are trying to replace your stock mirrors we do not offer any for your 2010 Ford Explorer XLT....

Why must the ball mount, #C45014, be used only in the rise position and not in the drop position? | I spoke with my contact at Curt and he said the Class II Drawbar, # C45014, has not been tested for use in the drop position. They only test...