Result: knobs

Have power at the controller, no lights at the knob. | Have power at the controller, no lights at the knob. | I would start by using a hook probe tester like the # PTW2993 to check and see if you're getting a power feed on the...

Or do I just convert it to a knob? | I have a boat trailer with a dico 60 hitch on it. Stamped on it states it fits 1 7/8” and 2” balls. I need a replacement latch, the part that grips the underside of the ball. Does the...

Is this knob the ground connection or what is the difference between the adapators that do or dont have this knob? | I have a 2003 4 Runner with tow package the factory hitch connection is 7 flat. I have a...

I have adjusted the adjustment knob out and the wheel spins freely but is still locking up. | Hello, the left front brake on a tandem axle is locking up when they brakes are applied. I have adjusted the adjustment knob out...

To level the sensor, you will set the power knob to maximum by fully rotating it clockwise (with the trailer connected). | Light on controller goes from green to a light green. No assist. Will not adjust with the riflght diel....

I currently have to manually turn a knob on the trailer when I back up to turn off the braking, Id like to convert that over to have this automatic if possible. | Good morning, I have a 1998 ranger 620 that is on a 1999 Wood/Ranger...

I made you a short video that shows how to replace the knob provided that the little tabs on the back of the knob or where they mount are not damaged. | While installing and checking operation, as I activated...

You are going to want the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional # RED52VR, don't forget to grab a Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 for one of those empty spots on your dash. |

To loosen, we depress this lever and we can rotate the hand knob counterclockwise to loosen from the trailer ball. | To loosen, we depress this lever and we can rotate the hand knob counterclockwise to loosen from the trailer...

As a test I held the P2 at no upward angle in my hand and applied the manual power knob, with no increase / improvement in braking power. | Hello eTrailer. I recently installed the Prodigy P2 Brake Controller on my 2017...

Check to be sure that the power knob is not set all the way to the lowest position. | I just hook up a pilot controller and if i hit the break pedal the dot in the middle lights up, but if i use the button on the controller...

Now for installing the knob of the controller you will need to pick a spot that you have at least 3/4" clearance for the knob, and 1-3/4" space behind the location for the back part of the knob to have enough clearance. |

It has a manual slide, a power knob on the right and another knob on the left. | Its a Journey model # 527408045 approx. 7 yrs. old. I lost my manual and want to set it up for a new trailer. Is there a manual...

Also no lights on the control knob! | How do you make the brake controller think it is connected to a trailer with brakes? Just to make the unit light up. I have no lights on the control knob. I do lights on the tester for...

The Valley Coupler #5122 on my trailer had a knob adjuster. I cannot find a replacement kit with the knob adjustment. | The Valley Coupler #5122 on my trailer had a knob adjuster. I cannot find a replacement...

Then rotate the Level Knob clockwise until you see a shade of orange on the light. | I have the four wires hooked up, have power to the controller. But it doesnt go from green to orange/red when I try leveling the sensor....

The main unit measures 3-3/8" long x 3-15/16" wide x 1-1/8" tall and the control knob measures 2-3/8" long x 3/4" wide x 7/8" tall. | Im interested in Redarc Tow-Pro Elite # RED44FR because the control can be hidden and placed...

This is with the power knob all the way clockwise. Thanks | My green light looks like its on with trailer disconnected but when my trailer is connected the green light is much brighter. Also, I was trying to adjust my level...

WHEN CONNECTED TO VAN GREEN LIGHT IS ON WHEN EMEGENCY BRAKE IS APPLIED ,LIGHT TURNS RED WHEN FOOT BRAKE IS APPLIED LIGHT STAYS GREEN NO MATTER WHERE THE POWER KNOB OR LEVEL KNOB IS. WHAT IS THE PROBLEM? | WHEN...

While we do not have the replacement locking knob you're needing for your ARKSEN bike rack we do have a wide variety of replacement bolts that we can help you with. | I have an ARKSEN hitch-mount bike rack, and a draw-tite...

How much do you tighten the adjuster knob once the ball is inside? | How much do you tighten the adjuster knob once the ball is inside? | The tightness needed for latching the Titan Zinc-Plated Brake Actuator # T43397007K to...

I see that the Redarc has a separate adjustment knob that you mount wherever desired. The knob then plugs into the control box and the Ranger factory wiring gets spliced into a 4-wire pigtail that then plugs into the controller to complete the installation. |

When I attach my trailer to my vehicle the control knob of the Redarc glows blue as it should. When I apply the breaks the color of the knob fades to purple then green which most closely resembles The LED Flashes an unusual colour sequence randomly whilst braking. |

What position should the power knob be in. I think I may have turned it off. I do not have a green power light showing anymore!! | What position should the power knob be in. I think I may have turned it off. I do not have a...