Result:

Yes, you can use the Center Rocker Switch # LC371010 in place of the magnet that comes with the Lippert Electric Tread Lite Step for RVs # LC353543 - you'll just wire the rocker switch directly to the motor like you see in the attached photo. |

If you need to hook up your junction box it will require ring terminals # 44-5310A, and 12 gauge wire # 12-1-1 to run to each light, and you can use a rocker switch like # PK34308 or Dimmer Rocker Switch # 37212275 to turn them on and off. |

Please recommend gauge and type of extra wire needed for three pads and 3 elbow joints wired to your recommended rocker switch. I only see black 16 gauge?! Also type of connectors needed to connect extra wire to pads and elbow wires and to connect to the rocker switch. |

If the wire from the battery to the Universal-Design Rocker Switch # PK34360 melted when installing the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat # 277-000163 it may have been that you simply need to use thicker wire, and I recommend 10 gauge # 10-1-1. |

If your trailer has an onboard battery then you can run the light to a switch like the Single Rocker Switch # 37212225, and then from here to a 12v circuit wired to the battery....

You should be able to use the In/Out LED Rocker Switch For Bulldog Winch # BDW20261 for your winch. | Will this switch work on all 4 pin winches mine is not a bulldog Im not sure the brand but its a4 pin.the...

How we typically recommend you do this is running a power wire to each camera yourself and then connecting them to a switch like the Single Rocker Switch with Bezel # 37212225. | HI We just...

This will give you a much more comprehensive field of view when driving to help you protect your blind spots while towing and is one of our most popular camera and observation systems. For the LED lights, if you're looking to create your own system with a switch located inside the coach you would want to start with the Optronics Flexible LED Light Strip - Weatherproof - White - 17' Long # UCL90CB; these lights can be hardwired to a switch like the LED Dimmer Rocker Switch - On/Off - Black # 37215225 to provide you with both power and dimming capabilities on this strip. |

The other option would be wiring the light directly to a dimmer switch that can be installed right inside your RV door and routed to a 12v power source to allow you the best solution for this....

To install these pads you'll need the following items to complete wiring to the battery/installing a switch: Switch: Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - 4-Blade - Red Pilot Light Item # PK34310 Spade Connector: Female Spade Terminal Quick-Disconnect - 16-14 Gauge - Fully-Insulated PVC - Qty 1 Item # DW01899-1 Butt Connector: Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10 Item # DW05745-10 Fuse Holder: Spectro 12-Gauge ATC-ATO Fuse Holder - Qty 1 Item # SWC9539 I've attached a video that goes over installation for you as well. |

These are rocker design switches. If you want a toggle switch for your lights I recommend part # PK34571. | Can I install this camera in front bumper where the license plate...

Then for a light switch you can use the Pollak rocker switch # PK34308 or toggle switch # PK34571. | We can help you mount a 12 volt battery to power the...

You can use the Pollak Universal-Design Rocker Switch # PK34310 between the battery and the pads as a way to turn them on and off. | Can you wire these be wired in series? I will be adding 4 to my camper. |...

Because of this I recommend routing the LED strip light to it's own source of power with 14 Gauge Wire # DW02414-1, Heat Shrink Butt Connectors # DW05744-5, and a Rocker Switch # 37212525. ...

I now have the above camera delivered from you and would like to run the power lead directly to the battery with a rocker arm switch located umder the dash area. This so I can use it at any time. | I now...

To connect the dome light, you can do that a couple different ways. The best way in my opinion is to wire it directly to the battery on the truck and use a rocker switch like part # BL0108-00 to turn it on or off as you wish. |

You will also need ring terminals # 44-5310A, and wire # 12-1-1 to run to each light, and to turn the lights on, a light switch such as the Pollak rocker switch # PK34308 or toggle switch # PK34571. |

Hooking up the junction box will require ring terminals # 44-5310A, and wire # 12-1-1 to run to each light, and you can use rocker switch # PK34308 to turn them on and off. | Hi I just bought...

This would then attach to the yellow reverse light wire on the Buyers 7-Way. Not the most elegant solution and you would need to find somewhere to mount that switch, but it could be done. | What is the best...

You can use 12 gauge wiring part # 12-1-1 (sold by the foot) and the Pollak Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - Black # PK34308 for the switch. | I was installing...

I recommend using the rocker switch # 37212595 which is labeled so it'll be easy to know if power is being sent to your lights (although you should be able to see if they're on or off pretty easily). |

Unfortunately the questions you are asking about timing, temperature, and consumption can't be answered by the manufacturer. If using a toggle switch, I recommend using the Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - 3-Blade - Red Pilot Light # PK34360, 10 gauge wire # 10-1-1, and circuit breaker # 9506P. |

Aside from using brighter lighting options, like the Opti-Brite # ILL06COB or # ILL39CB, you'll need the following: Butt Connectors - # DW05744-10 Ring Terminal - # DW05737-1 (per light) Self-Tapping Screw - # FA1131822 (per light) 16 Gauge Wire - # 16-1-1 (sold by the foot) Rocker Switch - # PK34310 You'll also need a ring terminal to connect to the positive post on your battery for power. |

Hooking up the junction box will require ring terminals # 44-5310A, and wire # 12-1-1 to run to each light, and you can use rocker switch # PK34308 to turn them on and off. | I have an enclosed...