Search: Trailer Jack Socket   >   !TC Truck Camper  x   >   Convert-A-Ball  x   >  

If your truck camper's rear Rieco jacks have contacted the front of your box trailer you'll need | Hello! I have a truck camper and I also pull an enclosed trailer. What is the minimum distance between the...

vehicleswith higher ground clearance. As is, I need to jack up with separate floor jack the trailer in order | I have a 2inch ball mount receiver welded by Weagant Farm Equipment dealer to...

I need to extend my hitch by about four inches so I can open my camper door past the trailer tongue | I need to extend my hitch by about four inches so I can open my camper door past the trailer tongue jack. I have an F350...

from center of hitch hole to center of ball hole so that my tailgate doesnt hit the trailer jack handle | I am trying to find a cushioned ball mount, 4inch drop , 2-5/16inch Ball that is at least 10inch from...

the jacks to slightly raise the trailer nose up a bit so that some of the weight of the coupler is off | I cant disconnect my gooseneck to 5th wheel adapter | I am not totally sure which fifth wheel to gooseneck...

What size of allen wrench, wrench sizes for set bolts and jamb nut, torque lbs, and socket sizes | What size of allen wrench, wrench sizes for set bolts and jamb nut, torque lbs, and socket sizes needed for complete installation?Thankyou...

We are having trouble locating a socket to tighten the square bolts..... Bought a 3/8foot drive | We are having trouble locating a socket to tighten the square bolts..... Bought a 3/8foot drive crow foot and adapter that will...

On average, the coupler height of a trailer that is jacked up so that it is level is between 17-19 | My new 2013 Pilot hitch receiver hole for a ball mount is 4inch higher 20.25 at its center than that of my...

. If you see the red line you need to lower the trailer jacks until there is no red showing before | What is the torque setting for the two bottom bolts on the bottom of the coupler where the red line is?? |...

I am renting a 5x8 Uhaul cargo trailer and I have a 2007 GMC Envoy Denali. What type of trailer | I am renting a 5x8 Uhaul cargo trailer and I have a 2007 GMC Envoy Denali. What type of trailer hitch do I need?...

on the trailer come apart? Or do you drill larger pilot holes on the top piece and stick socket through whole | If I buy the CAB c45x1216 How do I drill into the trailer. See attached. Does the hitch part...

To determine the rise or drop needed, jack up the trailer so that the frame is level to the ground | How we determine the correct for a ball mount hitch? Our Tahoe hitch is much higher than my brother-in-laws...

the trailer upthrusts from bumps this adapter if it has no such wear socket probably wont work | just purchased a Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter install went fine as did the hid-a-goose...

photo). It should then be a simple matter of jacking your trailer up high enough to clear | I purchased the convert a ball cab-c5g1216. I am having lots of trouble uncoupling from the ball on my BandW turnover...

to the ball so my tailgate opens without hitting the trailer jack. This unit is only around 9”. | Do they make a longer version of this cushioned ball mount. I would need at least 12” from the pin to the ball...

to take some measurements. Jack the trailer so that it is level, and then back the truck up as if you were | I have bought a 5th wheel camper and I need the adaptor coupler to go the the gooseneck ball in the...

the ground to the inside top of your receiver tube. Then, with your trailer jacked up so that it is level | I will be towing a 1250lb. 14ft long boat with my 2005 Honda Element. Should I set the ball mount...

. To determine the exact height adapter you need, Jack the trailer so that it is level, and then back the truck | do you have this n 16inch tall 2000 dodge 2500 with 3 inch...

need will depend on the coupler height of the trailer you're wanting to pull. With the trailer jack | I plan to buy the e98853 receiver. What is the correct ball hitch? I need a 1 7/8inch...

the trailer's jack to make sure the trailer is level before measuring. Measure from the ground to the bottom | I just installed the Draw rite 76128 2” hitch on my 2017 Honda CR-V AWD. I’m looking...

I have a Komfort travel trailer that I have leveled the coupler ball socket at 18inch from | I have a Komfort travel trailer that I have leveled the coupler ball socket at 18inch from the ground. The trailer...

found the Rack Jack II Hoist Item # 310-VRJ001 which is supposed to handle 300#’s. It appears I could | I currently have a RAM 2500 Limited 4x4, 6’4” Box and purchased the Companion RVK3600 for use with my Grand Design 295RL...

5th wheel travel trailer. Would you recommend the CAB-C5G for me ? my concern is clearance | I have a newer short box 1 ton truck with the BandW gooseneck built in and just purchased a 35foot 5th wheel travel trailer. Would...

turnover ball fit in that socket for the tundra? It looks like the ball for the tundra has a shorter shank | Looking at buying a tundra crew max with the 5.5 bed. Will the companion I have for the BandW turnover ball fit in...