!Stampede Travel Trailer  x   >   !TC Truck Camper  x   >   !Warrior  x   >   1985  x   >  

Would I be able to attach my license plate to this item? | I do have a taillight with integrated license plate holder but the Bargman LED Recessed Double Tail Light part # 47-84-527 would not allow for this. Instead, you would want to use the...

my Lippert Ground control leveling system lcd touch pad screen lights up but shows no read out is there any way to reset the touch pad so i know what i doing | I'm assuming you have a Lippert Ground Control 3.0. In some cases, we've found...

What is the brightest LED flood light you have. Preferably flush mounted or a mount that allows it to be angled/adjusted? | You would want to look at LED utility lights. I have added a link to them for you to view. Or you might be interested...

Hello, I am looking for a class IV hitch for a custom application. It is a 1985 Chevy C10 frame with a 1956 Chevy 3100 body and bumpers with a K5 blazer rear mounted gas tank. From what I can see, Curt 14082 should work for my frame width...

I want to put lights on my cab of a1985 custom Deluxe how do I do it.It has two roofs | We have a variety of roof mounted cab lights for your 1985 Custom Deluxe. Although there are many different types, the majority of them will have the same...

measured up a kwikee electric step. bottom step is 24inch wide and 10.75inch deep. has grip pad with yellow line across. tag under side said series 40 ser#30804 .. top mounting plate measured 24 3/8inch across.. any help in finding something?...

I have a1985 cj7 what set up Towbar do I use ? Do I weld a base plate or what do you suggest | In order to flat tow a vehicle you will need to install base plates first so the tow bar has something to attach to. For a 1985 Jeep CJ-7, you...

How thick is the hitch metal which I will be bolting to the frame of my 1985 El Camino? | The metal thickness, or wall thickness, of the cross tube of Curt trailer hitch # C12005 is 1/4 inch. The brackets on the sides of the hitch are obviously...

What type vent is of 27ft prowler fifth wheel? 1975 | If you can send me a picture of the hinge style for your 14" x 14" vent on your 1975 Prowler 5th wheel trailer I can help you choose the correct replacement lid from the linked selection. For...

I want a bike rack that will allow me to open the tailgate i also have a rear tire on the back. Looking for two Electric bike | From the image you attached, it the receiver hitch sets away from the bumper which is beneficial toward clearing...

I need a hitch for a 1985 itasca sunflyer with a p30 frome | I recommend looking at the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07. This is a universal receiver you can use as there currently is not a custom fit receiver...

I had the Curt two to three wire converter and two diodes not sure how to hook up the diodes Im also using a Toyota bed as a trailer I have three lights on each side brake lights bottom back up lights middle and turn signals top | In regards...

will this fit a 1985 gmc s15 2.8 v6 engine | The 2.8 liter GM motor for the 1985 GMC S-15 uses a filter thread size of 18 x 1.5mm and O-ring size of 2-3/4 inches. The Derale Remote Engine Oil Cooler Installation Kit, # D15751, has multiple thread...

I am considering buying a Valley Power Pull fifth wheel, I’m curious if you have the mounting rails to fit an 85 F350? | Valley has been out of business for many years, but unless it was one of their under bed mount system hitches, they all...

85 Toyota 1 ton long-bed pickup with your trailer hitch # 13086, could I tow a 2100 pound boat with this setup or would that be pushing the limits? | If you are going to purchase the Curt Hitch # 13086 for your 1985 Toyota Pickup, the hitch...

I have a 1985 Chevrolet G 30 class C motorhome 21Ft long with a 5.7 350 engine. I need to add a transmission oil cooler as I will be pulling a 14 Ft cargo trailer. I plan to install the cooler in front of the radiator unless you recommend to...

What part number do I need for the trailer hitch receiver that fits a 1985 4x4 Silverado | That is going to depend on what style 1985 Chevy Silverado you have. The Draw Tite part # 41947 will fit if you have 6 foot or 8 foot bed with standard...

Hi 1985 chevy K10. 1996 Northern Lite camper. 85 About 600 kgs. Would the stake hole style be stronger than the clamp on ? Thanks from Canada | The clamp on camper tie-downs like # HSSF make a more secure and stronger connection than the stake...

I need an axle... Its on a 1972 ezload trailer. The axle measures from outside of hub to outside of hub at 67 inches. The springs mount above the axle and are 48.75 inches apart. It also bends down 4 inches on the ends of the axle. It also has...

Is this the best option for my truck? I have a 1985 International S1900 dump truck. Thank you. Keith Claunch | I don't have any specs to determine fit of the Buyers Products Fabricators Hitch Plate like part # 3371809040 on any one vehicle but...

Trying to find the correct rear bumper mounting kit for my 1985 Nissan 720 sport truck. Purchased the Westin 61000 diamondstep universal bumper black finish | Per Westin-Fey, the correct mounting kit for to mount the Westin Fey Diamondstep...

Do the chrome bolts come with the bumper? | The Westin Fey Diamondstep Rear Bumper part # 71000 does not come with the mounting hardware and brackets. In order to install a bumper like this on your 1985 Chevrolet C/K Series Pickup you will want...

Do you make blackmax in any size | We do not manufacture/make the BlackMax covers. They are made by Extang and the replacement covers/tarps like the Replacement Tarp for Extang BlackMax Soft Tonneau Cover # EX1915 that you were looking at are...

I have a Curt A20 slider 5th wheel hitch that I no longer need on my 2019 Chev 2500 6 1/2ft box. A fellow with a1985 Chev 3500 8 ft box wants to buy it . Will it fit? Will he need a different installation kit? | Yes, he would need a semi-custom...