7-Way Trailer Plug Adapter or Compatibility with Lance Slide-In Truck Bed Camper
I am purchasing a lance slide In truck camper. Lance has a propriety plug for them. Do you guys sell a adapter that’s goes from a standard 7 way flat that came in my ram 3500 from the factory that adapts the lance plug? | Lance does have a proprietary...
Installation of Trailer Lights with Red, Black, and White Wires to Traditional Trailer Wire Colors
Have a harness that has green yellow and brown. But the tail lights are red black and white. What goes were | Red, black, and white wires are common on many tail light assemblies. When this is the case, you will have red as stop and turn, black...
Replacement Lens for Tail Lights on a 1999 Jayco Eagle Pop-Up Camper
I’m looking for taillight covers for a 1999 Jayco Eagle Popup camper 12 ft. I’ve looked everywhere for a platt number and cannot locate one. Wondering if you would have any suggestions. Thanks | If by tail light cover you mean a replacement...
Installing LED Lights On Trailer Connected to 2003 Dodge Dakota with Incandescent Lights
how do I wire LED lights on my trailer using 2003 Dakota vehicle with incandescent lights Clear confusion I have from reading so many articles on this subject. Some say you can just slap the LEDs on the trailer and wire back to vehicle using...
Converting RVST50 Style Trailer Taillight to LED
Can I just replace the old tail/stop bulb on my 2009 travel trailer with an led bulb? What do you recommend? | That depends on what taillight assembly your trailer has whether or not an LED is available for it. Could you get me a picture of...
Mounting Stud Length of License Plate Light
How long are the studs on this light, part # LPL82CBB? | I went out and measured the mounting studs on the license plate light, part # LPL82CBB, and they're right at 3/4 inches long. You'll need to source the nuts locally and I also recommend...
How To Ground Trailer Tail Lights Without a Ground Wire To a Wooden Surface
I am installing on wood. How do I ground? | The Standard Trailer Light Kit with 25' Wire Harness part # TL29BK as I am sure you noticed grounds via the mounting hardware therefore there is not a singular ground wire. In order to attach this...
Does Optronics LED RV Dome Light # ILL45CB Have Internal Switch
Does the RV lighting listed all have and on/off option or are they run off an electrical switch? I am looking to replace the original trailer lights with LED ones but not sure if they can run on their own with the on/off option. I dont see...
Gauge Wire for Use with Optronics Opti-Brite LED RV Dome Light # ILL36CB
Optronics Opti-Brite LED RV Dome Light - 227 Lumens, what size wire to tie these into other lighting | Since the Optronics Opti-Brite LED RV Dome Light # ILL36CB only draws .33 amps you can get away with a very light gauge wire. I'd go with...
Troubleshooting Trailer Running Lights Circuit of Vehicle Fuse Blowing with Ground Continuity
My 2017 trailer with 7 way plug blows the trailer running light fuse on my 2016 Canyon with factory towing package when the lights are on for more than 15 minutes. The only thing I can find that seems odd to me is the running light terminal...
Are The Opti-Brite LED Dome Lights Dimmable
Are these lights dimable | We do have an option from Opti-Brite that is dimmable, the Opti-Brite LED Dome Light, # OPT48FR. This is a 1,040 lumens, surface mount light that can be connected to either a 12VDC or 24VDC power source. This produces...
Do you Have to Change the Bulb in the Optronics License Plate Light # LP97CB ?
How to change the bulb? Im afraid to break it. How does it open? | The Trailer License Plate Light - Submersible - Gray Housing item # LP97CB is sealed which makes it waterproof and submersible. You wouldn't be able to replace just the bulb...
Replacement Marker and Clearance Lights For Globrite 118A/117R On a 2004 Haulmark Trailer
2000 hallmark trail it has globrite 118 A /117R can I get bulbs n cover’s for these lites ? | You are going to have to replace your running lights on your 200 Haulmark Trailer as I do not see that there are any replacement lenses available for...
10 Long 7-Way Cable With Double Ended Trailer End Connectors
Hello, Do you have this part in a 10 foot length? Thank you! | I have a couple options for you as we do not have a double ended 7-Way Molded Trailer Wire Connector in a 10' length. First you can take a 7-Way Molded Connector w/ 10' Cable...
How To Remove Optronics LED Clearance or Side Marker Light # MCL40RB For Replacment
I need to replace an MCL40RB side marker light on my travel trailer. How do I remove the lens from the existing marker without breaking the light? Once I have the lens off the light, how do I remove the inoperative marker from the trailer?...
How Does Demco Classic Base Plate Kit Install on 1978 Jeep CJ-5 Install
I have a 1978 Jeep CJ5 that I am wanting to flat tow. I have the original style stock front bumper. I am looking at the Demco Classic mounting brackets. Under the description it says attaches directly to the chassis. I’m trying to figure...
Parts Needed to Replace Entry Door Latch, Roof Vent and Amber Lens on 2018 Rockwood Mini Lite 2509S
Looking for a replacement roof vent lid see photo qty:1, outside orange/yellow led cover for the lights qty:4, and a replacement main door handle/lock qty:1 on my 2018 Rockwood Mini Lite 2509S | For the entry door handle you can use the Global...
Replacement Tail Lights For a 2021 Lance 2185 Travel Trailer
Looking for a replacement tail light for my 2021 Lance 2185. Specifications are as follows: 11 LED’s Length - 15 3/4” or 40 cm Width - 1 1/8” or 30 mm Space between screw holes - 14 1/2” or 37 cm Connection is offset from centre 6 5/8” from...
Will 4" Round LED Light Fit 4" Recessed Opening
Will these fit in a 4 inch hole? Looking for light that will fit an accutal 4 inch hole | The LED Trailer Tail Light # STL42RMB you're looking at has a lens with a 4" diameter but the hole needed to install it needs to have about a 4-1/4" to...
Will Optronics GloLight part # STL101RKB Fit 1/4 inch Thick Plate
What is the max thickness of plate this will fit? Need a light/grommet that will fit 1/4 plate. | There isn't a max thickness for the Optronics GloLight part # STL101RKB that you referenced but we know that it will easily work with 1/4 inch...
Can the Optronics LED Backup Light Part # BUL06CFB be Dimmed by Reducing Voltage
Does this light output the same luminosity across a wide voltage range? Does it get dimmer if below 12.8V and brighter above it? | The Optronics LED Backup Light for Truck or Trailer part # BUL06CFB is rated for 12 volts and can run at lower...
Recommended Round Trailer Marker Lights to Fit in 2-3/4 Mounting Hole
I have a 2011 PJ Dumper trailer with 2.5in grommet mounted round marker lights, they need to be replaced. The openings in the steel on the trailer are 2.75in, all the 2.5in lights I find are for 3in openings. What do I do? Does someone make...
How to Connect a Clearance Light with a Single Wire to a Trailer with Two Wires
1wire clearance light with 2 wires coming from train is there a positive and negative to identify | You can definitely wire a clearance light with a single wire to a trailer that has two wires. The first thing to know is that the two wires...
Does the Optronics LED Light Bar Illuminate the Spot and Flood Lights Separately or Combined
Can the flood light and spot beam be operated separately? | No, the Optronics # UCL25CB has only 1 set of wires so the flood and spot beams are designed to work at the same time. We currently do not carry a light bar that allows you to switch...
Filter Your Search
Contact and Help