10 Long 7-Way Cable With Double Ended Trailer End Connectors

Question

Question:

Hello, Do you have this part in a 10 foot length? Thank you!

asked by: Joe L

1

Helpful Expert Reply:

I have a couple options for you as we do not have a double ended 7-Way Molded Trailer Wire Connector in a 10' length.

First you can take a 7-Way Molded Connector w/ 10' Cable # 50-67-005 and add a 7-Way RV Style Trailer Connector # A7WCB.

Or you can connect 2 Hopkins 7-Way RV Style Connector w/ Molded Cables # HM20086 together if you prefer to have the molded and sealed ends.

expert reply by: Bud M

1

Answer 1

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Tim, The ZCI Circuit Protected Vehicle Wiring Harness #119250KIT is compatible with LED lights and has been used as a go to for years for people who have LED trailer lights. The light function is supposed send a tiny bit of voltage from the…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 10

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

10 Long 7-Way Cable With Double Ended Trailer End Connectors

Product Page this Question was Asked From

Continue Researching