!Jetta Wagon  x   >   1987  x   >  

I would like to buy 3 bent dog bone trailer hitch locks and 1 trailer tongue coupler lock, all black, and I would like them to be keyed alike. Also, I would like to be able to add hitch pins and tongue locks in the future and have them all...

I have an 87 Jeep Wrangler yj. I’m wanting to replace the upper door skins but everything I’m looking at has square corners on top the skins I have now are round. Does it really matter which ones I use. I’m not sure what brand I have they were...

Will a hitch meant for a 1996 ford f350 fit my 1987 chevy k20 frame width? Thanks | It would be quite unusual - and really lucky - for a hitch that fits a 1996 Ford truck to also fit a 1987 Chevy pickup. There are currently a wide range of...

I have a 1987 F350 Ford which had a SL16 installed. The hitch went with the trailer when sold leaving me with the Base Rails installed. This was the days before a need for sliding the hitch forward or back was needed. Id like to use the Base...

item fit 30 x 9.50 r15 tire? steve | The Bestop Large Tire Cover, part # B6103015 is designed to fit tires up to 30 inches in diameter and 10 inches wide. As your tire should be 30 inches in diameter by 9-1/2 inches wide, the cover should work...

If I remove one brake line on a tandem axle trailer will I have to bleed all four | If a brake line is opened on a braking system is common practice and recommended to bleed the entire system. There's a high possibility air entered the system...

My truck has a step bumper and I need a hitch that will handle a bass boat weighing 1200 lb. on a single axel trailer GVWR lbs. SM2500. Not sure what a deep bumper means? My ball mounts in a hole right behind the license plate. I want a frame...

What size ball will this need- Hitch Plate with Receiver Tube - Chevy/GMC Item # 3371809065 | The Buyers Products # 3371809065 has a 2" receiver, so you would need a ball mount that will fit in that receiver like the Curt Heavy Duty Forged...

Purchased the 1003-1 base plate for my 1987 Suzuki Samurai. Do I need to cut the bumper to attach the plate to the frame? Thank you | I took a look at the installation directions of the Roadmaster Crossbar-Style Base Plate Kit # 1003-1, and...

I am looking for a roof rack system for an 87 Samurai | For your 1987 Suzuki Samurai we have the Inno roof rack part numbers # INB117 and # INLD as a confirmed fit which would be an excellent choice! It's a square bar roof rack with a higher...

Will this 41910 hitch fit a 1987 Dodge 350 van. No step bumper, it is the bumper with rubber push pads on it. I will be using a cargo carrier which I will also purchase from you. Will the cargo carrier clear the bumper? Thanks | According...

1987 buick turbo with 3inch down flow pipe that has 4 bolt rear flange need to be around 14inch long | For your 1987 Buick Regal T-Type or Grand National we have the Magnaflow catalytic converter # MF93439 which is an exact replacement for the...

My truck has 2 gas tanks under the doors. Will these running boards work on my 1987 Chevy R30? | I have a solution for you. Unfortunately, I confirmed with Aries that the Aries Round Nerf Bars - 3" Diameter - Polished Stainless Steel # AA204041-2...

Will this fit in a hole close to 1 inch? | The Optronics Snap-In Mini License Plate Light part # LP11CB is designed to fit inside a 1-1/4" diameter hole, no more and no less. Therefore, if you only have a 1" diameter hole then you would need...

I have a 1987 F250 super duty my radio fried the other day and noticed my brake light was all that was working now their not working ether but I do have highbem headlights and dash lights but no blinker,hazards,running,reverse,lowbem headlights...

I have square Thule crossbars. Will this rack mount to these? Do you happen to have the installation instructions available? | The Curt Roof Mounted Cargo Basket, part # C18115, will fit on Thule crossbars. The mounting hardware on the Curt...

Even with no payload in the rear of my car, the rear is much lower than the front. Will this product provide any lift at all? Or do the bags even when fully inflated only push outward on the springs with no lift at all? Thanks | The Air Lift...

I purchased a wiring kit for my 1987 Nissan pickup and removed the driver sidw rear tail light grounded white wire mounted the converter and pluged wires in ran green wire across to other side and pluged in I only have tail lights on trailer...

I just got one of your sure step bumpers and I think I need the installation kit. Can you tell me which to order for my 1986 Jeep Commanche. I think it would be the same as the 1987 but Im not sure. Thanks | Westin doesn't have record of which...

IS THE MF39456 CATALYTIC CONVERTER C.A.R.B COMPLIANT AND LEGAL FOR CALIFORNIA EMISSIONS AND IF SO DOES IT HAVE A C.A.R.B EXECUTIVE ORDER NUMBER? | I do have a C.A.R.B. compliant catalytic converter for your 1987 Chevrolet El Camino w/ 5.0L engine,...

Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional. 1987 Ford F-series truck. | The Tekonsha Prodigy P3 # 90195 is an excellent choice of controller. It has preset brake boost options and an easy to read LCD screen....

i bought an 87 F250, and then an old camper to fit on it. it weighs 2100 lbs dry. it has a pigtail and a 7way plug that is meant to plug in just behind the driver inside the bed. i cannot decide which outlet i should purchase, or if i should...

Would this part work as a brake light converter? I have a 74 honda cb750 and am installing new lights 2 dual brightness led lights, 3 wires each low, bright, and ground and would like a way to wire them as the tail, turn, and brake lights. Bike...

would this unit power a mini dorm fridge Go Power Heavy-Duty Modified Sine Wave Inverter - 1,000 Watts - 12V Item # 34280176 | I have a solution for you, but the Go Power Heavy-Duty Modified Sine Wave Inverter - 1,000 Watts - 12V # 34280176...