Result: parallel kit

to make it level when connected to my truck. Do you sell block lift kits for this purpose? I can not find | I have a 2015 keystone sprinter 5th wheel, leaf springs over axle. I need to raise the camper up to make it level when...

not the typical install parallel with frame. Will I be able to install JT’s Strong Arm stabilizers and if so | My SportTrek 290vik has stabilizer jacks installed at 45 degree angles at each corner not the typical install parallel...

I will be happy to explain how to install the shock kit # LC281281. In addition to the instructions | Hi, could you tell me how these are installed? | I will be happy to explain how to install the shock kit # LC281281. In addition...

I will be happy to explain how to install the shock kit # LC281255. In addition | Hi, could you tell me how this product is installed? | I will be happy to explain how to install the shock kit # LC281255. In addition to the...

I will be happy to explain how to install the shock kit # LC281255. In addition | Where are the instructions located on this website? | I will be happy to explain how to install the shock kit # LC281255. In addition to the...

I will be happy to explain how to install the shock kit # LC281255. In addition to the instructions | Installing the Lippert Components Trailer Suspension - LC281255 I purchased from you awhile back. No installation instructions...

and make a mark on the I-beam parallel to the shock mounting lip on the tie plate. The shock should be up | How do you measure the length of a shock? From where to where on the shock? | I will be happy to help explain how...

I am looking to mount this shock kit on a 1969 Fan Lee Liner 18foot 15foot box it has a 3inch | I am looking to mount this shock kit on a 1969 Fan Lee Liner 18foot 15foot box it has a 3inch single axle, 6 leaf springs, and...

There isn't really a suggested angle at which to mount the Lippert shock kit # LC281255 as long | Can you tell what the best angle is from perpendicular. I know not more than 45 degrees, but is 20 better than 30 or 35. Also...

The Lippert shock kit # LC281281 will fit the 3 inch diameter round axles on your vintage trailer | My question is I have 3inch axle and the distance from the top of plate to the top of the frame is 9inch the height of the...

3/8” on the diagonals measured from center of ball hitch. The rear axle is 3/8” out of parallel | Question. Our new tandem axle boat trailer axles are out of alignment. The front axle is out about 3/8” on the diagonals measured...

to the shock mounting lip on the tie plate that is the same distance and make a mark on the I-beam parallel | Please advise which Lippert shocks I need. My trailer measures 11.5inch from bracket to bracket parked unladen. Thank...

instead of the current parallel to front and rear alignment would add more stability? Do you have | Hi - I have a 2020 Gulfstream Vintage Cruiser 23RSS I want to replace the OEM scissor jacks with stronger jacks and looking...

the Lippert shocks LC281281 not possible for a total of 4". Reference step 8 below of the shock kit | I will be installing the Lippert Components Center Point by Trailair Air-Ride Suspension Upgrade - Tandem Axle LC1565391....

How do you get the wires through the the brackets on the Lippert flex guard double kit | How do you get the wires through the the brackets on the Lippert flex guard double kit | The black flex guard will slide through the longer...

the correct side I recommend measuring your awning rail and choosing based off of that. These kits also | I have a 7’ and a 15’. Bracket to bracket slide outs, and would like the awnings to be black. What sizes would you...

RV Slide-Out Kit Hardware # LC1346271, and also sent you a link which has the install instructions | How does this attach at both ends? And where to attach as a blowen tire broke all the flex guard off at atboth ends. Thanks...