Result: Boat Loading Guide

I have a ez load boat trailer with tandem axles. I believe the axles are 3500lbs axles. I currently have surge breaks that haven’t worked in years. I need new bearings and seals and think it’s time to just get breaks back on my trailer....

Id like right and left rear corner blind spot cameras on my boat trailer to help me back into my narrow boat garage. I have Furrion rear corner cameras on my fifth wheel camper that I never use. Can they safely be repurposed to replace my...

Trying to install it on a boat trailer for a 1994 Maxum 20 foot boat. Installation instructions? | I attached a link to the right that contains detailed installation instructions for the Titan Zinc-Plated Brake Actuator # T43397007K that...

Hi there I have a 2006 EZ loader tandem Axle boat trailer for my 24 ft glastron. The current brakes are a four-wheel hydraulic drum system that needs a complete overhaul. Looking for everything from as xle out. I recently bought the boat and...

I have a Coyote Boat Trailer with two 3500lb axles. I need to replace all 4 hydraulic disc brake calipers and 10inch disc/hub assemblies. It currently has Knott brakes/calipers etc. Is there a compatible brand to replace Knott with same...

I have a 2002 Load rite dual axle bass boat trailer. I need a new actuator with the lock out solenoid. Please let me know what brand/model would work for this trailer | The Dexter DX7.5L # DX56FR would be a great actuator replacement for your...

I have replaced tires on my boat trailer because they had bad where on the inside. Do you think the wear on the tires is because of the axel. Its is just the right side tire that is wore down. | Boat trailer tires that are wearing on the inside...

Hello Would there be any issues installing this on a LoadRite 16 ft. trailer, 16F1200WT. Weight capacity is 1200lbs, not sure of the tongue weight. If it Is ok to use it, is there a specific distance from the coupler that the hinge needs to...

I need to replace the actuator on my boat trailer. It came with a 2012 Skeeter zx21. It reads A-60/A-75 on the tongue but I cant get the numbers to match exactly to your model numbers. Can you guide me to the appropriate one? I do want the electronic...

I have a Load-Rite boat trailer with a torsion axle that sits too low. The skeg of my outboard is scary close to the ground. What are my options to raise ride height? | You can use a torsion axle lift block to raise your Load-Rite boat trailer....

The shackles are 3 inch center hole to center hole. | For a new hub/drum that will work great with your current axles you'd want the part # 8-201-5UC3-EZ and then for brake assemblies you'd want the # AKEBRK-7-SA which are self-adjusting. To...

I just got a 1988 Cox tandem axle boat trailer with boat, but it is not equipped with brakes. The four hole backing plates are on each axle. The boat et al weights in at about 3500 lbs so by WI law it needs brakes. Just what specifics do I have...

Hello, I read the info sheet about adding 2nd axle to boat trailer. My question is when e de determining tongue weight the picture references the trailer weight,does it not matter about total load weight with the boat on the trailer Thanks...

Hello, I have an 2006 EZloader boat trailer with tapered spindles. Im looking for a bearing kit. The Timken bearing kit looks like all the right part numbers except the seal. The seal ID is too large and is single lip. ID needed is 1.68inch...

I have a 1995 Mastercraft Prostar 205 boat. The boat is on a single axle manufacturer original trailer. I am having problems with tire sidewall scrub in the wheel wells when hitting bumps. I’m not sure if this is an original problem or if the...

I’m looking for a complete idler hub assembly for a 2002 load rite tandem axle boat trailer. It’s 6 lug VIN 5A4NF5V28220XXXXX | You are needing either the Galvanized Dexter Trailer Idler Hub # 8-213-51 or Stainless Steel Kodiak Trailer Hub #...

I have a 30 foot 7500 pound boat. My trailer has four disc hydraulic break system What is the right actuator for my trailer? | A surge brake actuator will need to be based off of the gross vehicle weight rating (GVWR) of the trailer with the...

do you have a caliper rebuild kit for a knott caliper AKK 6B6284 202004161323 ARE NUMBERS ON CALIPER ITS ON A 2021 LOADRITE TANDUM BOAT TRAILER THKS | Hello Mark, thanks for reaching out. We do offer a few caliper rebuild kits, but I am sorry...

I have a custom made boat trailer with 5 on 4-1/2 hubs, 14inch wheels, with LM67048 inners, and LM11949 outers with no brakes. At least one of them seemed to be an EZ lube hub, but Im not certain. They werent in good shape and one of the bearings...

i have a 2005 loadrite tripple axle 12500lbs boat trailer currently with a carlisle gen 5 electric over hydraulic with disk brakes. can i remove the gen 5 and replace it with a electric surge actuator? gen 5 needs to be replaced and current...

I have a 2004 EZ Load trailer for a Skeeter boat. I am replacing bearings and thinking it may be simpler to replace the hubs? Inner bearing is L68149 and outer bearing is L44694. The Seal is 2.56inch x 1.68inch according to the book I...

On a boat trailer that was converted to electric brakes, how are the brakes applied if the trailer breaks away from the tow vehicle ? Any help would be appreciated! Thanks | On a boat trailer with electric brakes you will use a breakaway kit....

Will this help with my ‘05 F250 w/a 6” lift, that’s typically loaded with tools and pulling a 24’ boat w/ a large motor sway and sag are my main issues? I haven’t seen any of these trucks mention being lifted. | Hey Thomas, Yes, the RoadActive...

Hi - I’m getting ready to order Kodiak disc break kit K2R526DKG 12”6 on 5-1/2 and have an existing TDE model 16.5 actuator on my recently purchased 2016 boat and trailer. I’m looking at the Demco Listed at 494.15 with 16k load rating vs the...