!Pleasure Way  x   >   !Ram Pickup  x   >   !Jetta  x   >   CE Smith  x   >  

I just installed some bunk boards on my pontoon trailer and there isnt much clearance from the too of the board, about 1-2inch between board and floor braces. Is that too close? | If there is no flex in the bunks with the pontoon boat loaded,...

I assume there is no need for a center cap with this wheel design? Also, takes standard 60 degree 1/2-20 Lug nuts ? Can I go with basic lug nuts as they are not visible anyhow ? | The Aluminum Hi-Spec Series 6 Trailer Wheel # AM22651 does include...

I just installed smith model 27671 pontoon bunk guides on my trailer. I put one pair at the rear inside and another pair about halfway on inside of the trailer. They are 3inch from the pontoons and 1.5inch clearance between the floor rails....

Do you or CE Smith have any recommendations with respect to fastener torques, especially for the fasteners that do not span a frame rail section? The only torque specification pertains to the lug nuts. | I do have some advice for you but CE...

Is the spool roller assembly CE32100G available without the rubber roller? | The closest thing that we carry to the roller assembly # CE32100G at this time is the Panel Bracket # CE10300G. This does not include the shaft or the end caps, so...

Which lug bolt is required for this wheel, 60° or 90°? | For the wheel in tire and wheel combo # AM89992 you will want to use 60 degree coned lug nuts or wheel bolts. Specifically you can use # CE11051 (sold in quantities of one). This is a...

Hello, Do you offer the CE17920 28.5inch Long Fender with a welded in backing? Thank | The closest fender we offer to the part # CE17920 that has a welded back plate on it is the part # HP36VR which is a few inches longer. It's dimensions are...

Re: CE Smith gussets What is the measurement of the flat part of the gussets, both for the 5-1/2 and 6-1/2 Thanks | The flat center portion measures 3 inches for the CE Smith Gusset for Boat Trailer Frames - 5-1/2" Long # CE26240A40, and 4 inches...

how many inches is it from the top of swivel bracket, if setting horizontal, to the top of the first u bolt mounting hole? I want to know how low I can make this bracket sit, when bolted through with u bolts. | I went and pulled CE Smith Double...

I see you have the non galvanized hub that can be bought pre-greased...can a person buy the galvanized pre-greased? | Yes, we do the CE Smith Trailer Idler Hub Pre-greased with case part # CE13515 is the same galvanized hub as part # AKIHUB-545-35-G-EZ-K...

what type of roller assures that the rear of the boat stays centered while loading the boat on the trailor? | Sounds like you are referring to guide on rollers like the CE Smith Roller-Style Guide-Ons for Boat Trailers # CE27610. These mount...

What is the spacing of the holes in the tongue that this part is designed for? | I went out to our warehouse so I could take a measurement on the CE Smith Tongue Skid # CE30002G. I found that the existing mounting hole and tab are designed to...

I have a trailer with 15” diameter tires to include the rim it is fixed to What size covers should I use? | Thank you for sharing your photos. Your tire is a 4.80/4.00-8 and for a spare tire cover for this tire size I suggest the smallest...

This bracket should work on a cradle lift for pontoon also? I have 3 cross bars so could use 6 of these. The cradle is 10foot what length size of 2inch X 6inch would you recommend? Was thinking 14foot to hang off 2foot each end? I have a...

The fender CE17900G is pre galvanized. Video says it can be painted. Does this have to be painted or can I just leave it as is without worrying about rusting? Thanks | A pre-galvanized fender like the part # CE17900G would not have to be painted....

How much adjustment to the on each side of the trailer will the Smith roller guide on allow? # ce27610 | The CE Smith Roller-Style Guide-Ons for Boat Trailers # CE27610 measure 17-1/2 inches horizontally. It mounts on 3 inch frames and roughly...

What is the rating on the installed valve stem and what type of lug nuts should be used? | The valve stem specs are specifically listed but the highest load capacity tire that fits these wheels is a 225/75-15 load range D rated for 65 psi so...

I have a 28foot Bayliner and Id like to get bunk guides for the trailer. My trailer rails are 6 tall and it doesnt look like your products will fit that. Is that correct? | For your 28 foot Bayliner trailer, I recommend the CE Smith Bunk-Style...

Do you have a trailer similar to the: CE Smith Multi Sport Plus Boat and Kayak Trailer w/Bunks - 12 wheels that will accept a 16 flat bottom boat? Please let me know. Thank you very much. | We do have an option similar to the CE Smith Multi...

I have a single axle 10foot carry on brand utility trailer that I am trying to lift. Would this feasibly work to extend the leaf shackles? I cannot do a traditional axle flip because the axle is bowed. | We have over under kits that allow you...

I am looking for options to support the bow of my 14foot tracker topper jon boat while trailering. I looked at the CE Smith Carpeted Johnboat Bunk Board for Boat Trailers. However, it seems the boat would sit on the ribs on that board and...

need a couple of rollers to start my 15 ft Lowe boat will 2 of the TRP-5 in roller help starting the boat onto trailer . I put on new bunk carpet and its like you put brakes on witching it on | Yes, the CE Smith Spool Roller part # CE10451G...

I am interested in a spare tire cover for a Kia Soul, The tire size is 205/55/R16. Which size cover do I need? | The overall diameter of your tire size 205/55R16 is 24.88 inches so for a white cover you'd want the part # 052963751109 or for...

Are there big differences in the CE Smith and Fulton 14inch models? I am going to replace the black ones on my Shorelandr trailer that has current ones that look like these. Is one sturdier than the other? Or thicker plastic? I can stand on...