Best Disc Brake Setup for Dexter 8k Torflex Axles
Hello I was speaking a while ago about a kit to convert my wellscargo gooseneck trailer to disc brakes and was Interested if you could put together a kit for me with everything I need. I have the dexter 8k torsion axles with 17.5” wheels. Would...
Will the Titan Premier Disc Brake Kit Fit with 13 Inch Wheels
Looking to replace my current brakes on my boat trailer. They are ufp db-35 setup with 13 in rims. Will the titAn brake kit work with 13 in rims | I have a solution for you, but the Titan Premier Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 -...
Replacement Electric Brakes for Dexter PR-FF SEC-FF 5.2KPR-GGSEC-GG 12X2XQ 36-89
Hello, I have brakes on my trailer that I need to replace. On the outside of them they say PR-FF SEC-FF 5.2KPR-GGSEC-GG 12X2XQ 36-89. What brake kits do I need to replace these with? Are they the 5.2K Axles or 6K? Thank You!! | Based on...
Is Spindle Available For Kodiak 12 Inch Hub And Rotor Assembly For 5,200 - 6,000 Lb Axles
Can you provide the part numbers of the spindles that you stock that will work with the KHR12 hub? | We do not offer a spindle that will work with part # KHR12D. This hub is designed to fit 5,200 - 6,000 lb axles and wheels that are 15 inches...
How to Tell if a Bolt is a Grade 8 Bolt
Is this a grade 8 bolt drive type 9/16”-18 x 2.25 | If you look at the attached photo of the Kodiak Wheel Bolt # K916WB25 you will notice that it has 6 lines on the head. This is an indicator that it is a grade 8 bolt. The Kodiak Wheel Bolt...
Will Kodiak Disc Brake Kit, # K2HR712 Fit a 7,000 Pound Dexter Trailer Axle
Will this disc brake kit fit a Dexter 7000lb axle? | Yes, the Kodiak Disc Brake Kit, # K2HR712, will fit 7,000 pound Dexter trailer axles. It is also designed to fit 16 inch and larger wheels with an 8 on 6-1/2 inch bolt pattern. You can check...
Do Trailer Hubs # AKHD-545-35-EZ-K and # AKHD-550-35-K Fit Same Spindle
I want to replace surge brake system with Electric. The bearing numbers are L44649 and L68148, the current pattern is 5 on 4 1/2, I want go 5 on 5. Looking for the part numbers for backing plate and hub drum assembly. Is AKHD-545-35-EZ-K and...
Replacement Brake Pads for 2002 Ranger 620 Trailer
Do you happen to have brake parts for a 2002 ranger 620 trailer Brake pads Brake pads slide clips Caliper slide bolt | The Disc Brake Pad & Lining -10K & 12K - (One Wheel) # BP04-400 are the closest thing we carry to the appearance of the...
Complete Electric Over Hydraulic Brakes Set Up With Tandem 3,500 lb Timbren Axle-Less Suspension
I have a boat trailer with tandem axles. I have surge and want to change to electric controller. I am completely changing the entire system. Please bid the Timbrens with as much stainless steel as you can get. I will need a list and price from...
Replacement Brakes, Bearings and Seals for a 10k Trailer Axle
I have some 10k dually trailer axles on my trailer made my general. Serial number 61613 and I am trying find find replacement brakes and bearings and seals with shoes. And I would also like to find the disk brake conversion kit. I need help...
Recommended Disc Brake Kit to Replace Electric Brakes on Fifth Wheel Camper
I would like to convert my 2017 VanLeigh tandem axle fifth wheel 7K Lippert axle to disc brakes. Do you offer a complete kit including brake lines with a Dexter actuator and Kodiak Dacroment 13 hubs? Thank you for your help. Dennis | We have...
Parts Needed to Convert to Kodiak Disc Brakes on 5th Wheel With 7,000 lb Dexter Axles
I have a 2010 keystone 5th wheel trailer that I am interested in converting into disc brakes. The trailer has 2 7000 lb e-z-lube axles. I get lost on your website trying to find the correct Kodiak brake kits. Do you have any suggestions? | We...
Replacement Oil Bath Hub Cap for Dexter Trailer Hub
What is the part number for the oil cap for this hub as I need to order one? Thanks | The Oil Cap, Plug and O-Ring # RG04-230 is the replacement for the Dexter Trailer Hub and Drum Assembly # 8-219-9UC3-A. You will want to remember some Synthetic...
Will Kodiak Disc Brake Kit Replace UFP Brakes On 5,200 Lb Torsion Axle
I am replacing the brakes on a Magic Tilt boat trailer. It is dual 5.2K axles with UFP brakes currently 12inch rotors. I would like to try the Dacromat/Stainless package from Kodiak, but I am concerned about getting the calipers properly mounted....
Can Electric Over Hydraulic and Surge Brake Actuators Be Installed At the Same Time
I have a follow-on question to one posted about converting surge brakes to electric over hydraulic. I understand that leaving a surge coupler in place and locking it out is acceptable when converting to electric over hydraulic. What Id like...
Parts Needed to Add Disc Brake Kit to Dexter 8,000 lb
looking for retro fit disk break kit for Dexter pre 2013 oil lube 8,000lb axles with actuator do you sell HYDRASTAR tandem kit? | What you would need is the Kodiak Disc Brake Kit part # K2HR89DD (one for each axle). And then for a the pump kit...
Replacement Parts for Wheels and Disc Brakes Getting Too Hot on Boat Trailer
Im getting high heat from the back set of wheels to the point that I can smell the grease cooking , people are telling me that the brake systems I have are prone to calipers getting stuck ,do you carry parts to work on this 2000 model trail...
Replacement Oil Seal and O-Ring for Dexter Drum Hub with Oil Bath
Good afternoon I was inquiring about brake drum # 8-430-5uc3 my question do they sell the seal and the o-ring seperatly Thanks | The Dexter Trailer Hub and Drum Assembly - 9,000-lb to 10,000-lb - 8 on 6-1/2 - Oil Bath - Non-ABS Drum # 8-430-5UC3...
Hub Assembly for Big Tex Trailer With Tandem 12k Axles
I have a customer looking for a hub assembly for a Big Tex Trailer 12k axles dual with disc brakes. Do you carry this item? | We do offer one 12,000 lb idler hub assembly which is the Dexter # 8-214-8UC1. This uses # 3984 inner and # 28682 outer...
Oil Bath Cap for Dexter Hub 8-248
I have a Dexter 8-248 hub and am looking for an oil bath cap for it, are there any available for this model? | Yes, since the hub bore of a Dexter 8-248 hub is 1.98 inch the correct oil bath conversion cap would be the part # xlprolube1980. |
Guide Bolt Dimensions for Kodiak 3,500 lb Disc Brakes
what is the length of slider pins on Kodiak k2r35d? Im concerned theyd interfere with the trailer frame. thanks. | The overall length of the bolts for the caliper on the Kodiak Disc Brake Kit # K2R35D is 3" (see attached). |
Parts Needed to Convert 10k Trailer Axles from Electric Brakes to Electric Over Hydraulic
Hi - I have a 1994 interstate 20 ton tag trailer, tandem dually with electric brakes. What other parts would be needed to complete the set up? I assume that I would need to have brakes on both axles? some sort of tank? lines? I already have...
Which Kodiak Brake Kit Fits 8,000 lb Dexter Axle
will an 8000 lb Kodiak disc brake kit fit on a 7000 lb Dexter torsion axle? | For your Dexter 7,000 lb torsion axle the disc brake kit you'd want is the Kodiak part # K2HR712D which is the right capacity, fits your spindle, and is Dacromet coated...
Are Additional Parts Needed to Replace 250 Kodiak Disc Brake Calipers
I have a 2007 fiver with Kodiak 250 calipers on 7k axles. Would like to replace one problematic caliper. Will the current new ones be a direct replacement, without needing any other parts? | You won't need any additional pieces when replacing...
Filter Your Search
Contact and Help