Trailer Lights Specs:
Features:
2-1/2" x 1-1/4" x 13/16". Waterproof trailer light illuminates your license plate. Clear lens under polycarbonate housing. Surface mount - requires bracket (sold separately). Accepts standard 2-prong plug.
More Information >Trailer Lights Specs:
Features:
2-1/2" x 1-1/4" Rectangle. Waterproof LED trailer light illuminates your license plate. Requires mounting bracket or grommet (sold separately) for installation. 2-Wire pigtail with power and ground wires. Clear lens.
More Information >Trailer Lights Specs:
Features:
2-3/4" x 1-3/4" Rectangle. Low-profile trailer reflector increases visibility of vehicle in low lighting. Spitfire design has 50 percent wider angle of reflectivity than conventional reflectors. Adhesive backing for easy install.
More Information >Trailer Lights Specs:
Features:
2-3/4" x 1-3/4" Rectangle. Low-profile trailer reflector increases visibility of vehicle in low lighting. Spitfire design has 50 percent wider angle of reflectivity than conventional reflectors. Adhesive backing for easy install.
More Information >Videos
for RV Exterior Lights
Help Articles
for RV Exterior Lights
Expert Answers
for RV Exterior Lights
Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
view full answer...I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where…
view full answer...The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be…
view full answer...The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x…
view full answer...The first thing to do is disconnect the trailer from the Liberty. Then using a circuit tester, like part #PTW2993, test each pin of the 4-Way. Clip the alligator clip of the circuit tester to the exposed post, the ground wire. Check each pin with…
view full answer...The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...I checked directly with BOLT for you, and they confirmed for me that your 2021 Chevy Silverado is absolutely compatible with their trailer hitch locks. Take a look at the accompanying photo, and if you have the same center cut key, the correct lock…
view full answer...Yes, the Bolt Trailer Hitch Lock part #BL7023582 will work for you as it is a hitch lock designed for 2-1/2 inch hitches like what you have on your GMC 3500 truck. The usable portion of this lock is 3.55 inches. Check out the picture I attached for…
view full answer...The Dexter 10K electric brakes #23-439 (right side) and #23-438 (left side) will have to be manually adjusted using the adjustment wheel below the magnet. To adjust the brakes you will use a small screwdriver or similar tool to turn the adjustment…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...