RV Covers Specs:
Features:
Protect your 5th wheel during storage with this heavy-duty cover. The UV-resistant, water-resistant cover is made of polypropylene. A unique triple layer top panel provides maximum resistance to rain and snow. Length is 36'.
More Information >RV Covers Specs:
Features:
Protect your 5th wheel during storage with this heavy-duty cover. The UV-resistant, water-resistant cover is made of polypropylene. A unique triple layer top panel provides maximum resistance to rain and snow. Length is 36'.
More Information >Videos
for RV Covers
Help Articles
for RV Covers
Expert Answers
for RV Covers
Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…
view full answer...Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to…
view full answer...A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
view full answer...When measuring for a trailer cover you want to measure from the front of the trailer box, not the tongue, to the rear including anything that is attached to the rear. This will include a spare or a ladder at the farthest edge at the rear of the…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…
view full answer...You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.
view full answer...There is a hitch receiver that could work for your 1995 Chevy G20 van, so long as your van does NOT have a step bumper. If so, I recommend the Draw-Tite #75121 hitch, this is a 2" hitch that is a complete bolt-on installation so there will be no…
view full answer...If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.
view full answer...