Does Lock N Roll Articulating Trailer Hitch Setup Allow More Sway

Question

Question:

Hi, Does the use of a Lock n Roll articulating hitch exacerbate sway? Thanks.

asked by: Tom

0

Expert Reply:

The use of Lock N Roll Articulating Trailer Hitch for 2" Receivers # 336VS501 does not add sway to the setup. Couplers normally can articulate to the left and right like what this allows so it would not be any more prone to sway than a ball style coupler.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I reached out to Lippert to confirm and the Kwikee SuperSlide Tray Assembly with Trim Kit for RV Cargo Compartment part #LC370769 is adjustable as far as width goes. It is up to you to choose how wide you want the tray to be. Some will choose to have…

view full answer...

Answer 2

We have a folding trailer tongue hinge that could work for the purpose you describe, as long as your trailer frame isn't constructed of aluminum. You could use the Fulton Fold Away Coupler Hinge, part #FHDPW330300. The hinge kit is designed for 3…

view full answer...

Answer 3

Unfortunately, there isn't a way to use the #336VS501 Lock N Roll articulating hitch while using weight distribution. The good news is that we do offer a cushioned weight distribution shank, part #AMAC1. The shank has a 10K towing/2000 tongue…

view full answer...

Answer 4

The vehicle side of the Lock N Roll Articulating Trailer Hitch #336VS501 can be locked to the vehicle's 2-inch receiver hitch using any standard pin lock such as #e98880. The mating part that bolts or welds on to the trailer #336TS508 will only…

view full answer...

Answer 5

The #336VS503515 comes with the adjustable channel bracket along with the adjustable channel mount and bolts. You will need to install the channel mount in the appropriate rise/drop position since it does not come fully assembled. It looks like you…

view full answer...

Answer 6

Welcome back! The Lock N Roll Articulating Coupler #336TS504 is listed as a weld-on application but if you want to bolt it on you'll need to drill some 5/8" holes. Most of our bolt on couplers have 3 holes on either side spaced 2"…

view full answer...

Answer 7

Hey Don, Lock N Roll has their own Weight Distribution System - Trunnion Bar #LR27VR to connect to the Lock N Roll Articulating Coupler - A-Frame #336TS504. This WDH is rated for 11,000lbs GTW/1,100lbs TW, matching the capacity of the coupler as…

view full answer...

Answer 8

Hello Jody. I had one of the Specialty Recreation Single Bowl RV Bathroom Sinks #SR26RR pulled from our warehouse and measured. The sink is 13.5" tall overall, it is 10.5" deep on the side and I measured 15" across diagonally. I made a…

view full answer...

Answer 9

Hey Drew! If you're wondering how far the #LR76VR will stick off the front of the trailer when installed that would be 2". I went ahead and attached a diagram below with some general measurements for your reference. If you're looking for…

view full answer...

Answer 10

Based on the images you sent in it appears your 2005 Starcraft RT10 does not use a traditional A-Frame coupler so the Lock N Roll #336TS504 will not work for your application. Instead you will need to measure the width between your frame rails the…

view full answer...

Answer 11

I went out to measure the Lock N Roll Articulating Trailer Hitch for 2" Receivers - Vehicle Side #336VS501 and found the distance from the center of the hitch pin hole to the back of the latching mechanism is about 6", the length from the…

view full answer...

Does Lock N Roll Articulating Trailer Hitch Setup Allow More Sway

Product Page this Question was Asked From

Continue Researching