Recommended Clearance Light And Grommet For Older Snowmobile Trailer Rebuild
Question:
I am rebuilding a older snobird snowmobile trailer, guessing around 1992. I have a hole that measures about 2 5/8inch hole for a clearance light. What size sealed round light will work in this application that uses a rubber grommet ?
asked by: Eric S
Expert Reply:
The clearance light I recommend for your snowmobile trailer is part # MCL57RB. This is a 3 diode 2-1/2 inch round light. It does require a rubber grommet for installation.
The grommet to use for installing this light I recommend is part # A57GB. You may need to take a small round file and open the mounting hole you said measured about 2-5/8 inches but this should work well for your trailer.
To connect the light to your trailer wiring I recommend using the Two Wire Pigtail, part # A46PB. If a right angle plug is needed you can use part # A49PB.
Products Referenced in This Question
Right Angle 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead
- Accessories and Parts
- Trailer Lights
- Wiring
- Plugs and Pigtails
- 6 Inch Long
- Two Wire
- Right Angle Pigtail
- Optronics
more information >
Right Angle 2-Wire Pigtail for Optronics Backup and Utility Trailer Lights - 2-Prong PL-3 Plug
- Accessories and Parts
- Trailer Lights
- Wiring
- Plugs and Pigtails
- 10 Inch Long
- Two Wire
- Right Angle Pigtail
- Optronics
more information >
Rubber Grommet for 2-1/2" Round Trailer Lights - Recessed Mount - Open Back
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- 2-1/2 Inch Diameter
- Grommet
- Round
- Optronics
more information >
Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Round - Red Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 2-1/2 Inch Diameter
- Red
- Optronics
more information >
Product Page this Question was Asked From
GloLight LED Trailer Clearance or Side Marker Light - Submersible - 9 Diodes - Round - Red Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 2-1/2 Inch Diameter
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Trailer Wiring Diagrams
- Q&A: Replacement LED Marker Lights for Floe Pro 100 14 Foot Snowmobile Trailer
- Q&A: Brake Controller that Fits 2024 Motorhome on E350 Cutaway Chassis
- Article: Brake Controller Installation on a Ford Full-Size Van
- Article: Trailer Lighting Requirements
- Article: Brake Controller Installation: Starting from Scratch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Clearance Light Recommendation for 2-1/2 inch Hole In Flat Bed Truck
- Q&A: Recommended Replacement Ignition Knob for a Furrion 2-in-1 Range Oven
- Article: Troubleshooting Brake Controller Installations
- Q&A: Brake Controller Install Harness for Prodigy P3 for 2023 Ford E-350
- Q&A: Replacement 12 Volt RV Refrigerator for Norcold 2118
- Article: Testing Trailer Brake Magnets for Proper Function