Need a Dexter 3,500 Pound Axle with Hydraulic Disc Brakes, What Parts Do I Need?
Published 11/17/2026 >
Products Featured in This Question
Question:
Looking for a dexter3500lb axle with hydraulic brakes
asked by: Arthur M
Expert Reply:
Hello Arthur,
Thanks for writing in.
There are two important measurements you will need when picking out the correct axle: the hub face and spring center measurements (please see attached image). You can usually find these listed on your axle tag as HF and SC, although sometimes the measurements are coded into the axle number. You can check your axle tag or measure your existing axle to determine which one you need. I also attached a video where Connor shows you how to measure.
- 89" Hub Face, 74" Spring Center: Dexter Trailer Axle Beam - 3,500 lbs # T3584F-EZ-8974
- 95" Hub Face, 80" Spring Center: Dexter Trailer Axle Beam - 3,500 lbs # 7359765
If your measurements are quite a bit different, or if you need a drop axle instead of a straight axle, just let me know.
Both axle options will work with the Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 10" Rotor - 5 on 4-1/2 - 3.5K # HYD22FR that you were looking at, provided your trailer has the correct mounting configuration.
If you don't have some bearing grease on hand, grab some LubriMatic Prime Guard High Temperature Wheel Bearing Grease - Red - 16-oz Can # L11380.
A couple of things to keep in mind during installation. You will want to make sure the brake mounting flanges are properly positioned and that the brake lines are routed away from any moving suspension components or areas where they could rub or get pinched. Since you're installing disc brakes, you will also want to make sure the actuator is wired correctly and that all of the hydraulic connections are secure. I know what I am saying seems like common sense with the install, but people try to speed through it and it causes issues.
Once everything is installed, you will need to bleed the brake system to remove any trapped air. Start with the brake farthest from the actuator and work your way toward the closest. Keep an eye on the fluid reservoir throughout the process so it doesn't run dry, if it does run dry, you will have to start over. When we bleed the brakes at home, I keep an eye on the reservoir while my other half keeps an eye on when the air is gone. *Please check the instrtuctions on what brake fluid to use, I don't like to include that on my answer pages in case it changes over time.
What kind of trailer are you working on?
Product Page this Question was Asked From
Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 10" Rotor - 5 on 4-1/2 - 3.5K
- Trailer Brakes
- Disc Brakes
- Standard Grade
- 5 on 4-1/2 Inch
- Hub and Rotor
- 1/2 Inch Studs
- 3500 lbs Axle
- 14 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Hydrastar
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: What Is The Difference Between Hydrastar Kits HYD22FR And HYD42FR?
- Q&A: 2024 Forest River Wildwood X-Lite 273QBXL
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Q&A: Recommended Electric Over Hydraulic Conversion Kit for a Boat Trailer w/ 3,500 lbs Axles
- Q&A: Will Hydrapro Alpha G-1600X Electric Over Hydraulic Actuator Work on Boat Trailer
- Q&A: Recommended SnapPad Jack Pads for a HWH Leveling System on a Motorhome
- Q&A: Comparing DeeMax and Hydrastar Disc Brake Kits
- Article: RV AC Not Cooling? What's Normal, What to Check, and When to Replace
- Article: How to Choose a Trailer Hitch Coupler
- Article: Trailer Wiring Diagrams
- Article: Is It Illegal to Leave My Hitch on My Truck?
- Article: Brake Controller Installation: Starting from Scratch
- Article: Double-Eye Trailer Suspension System Review
- Article: Best Boat Trailer Jacks





