Does etrailer Round A Frame Trailer Jack Come With Mounting Hardware?

Question

Question:

Does this come with replacement bolts and nuts? Or do they need to be purchased separately? A-Frame Trailer Jack TJA-2000S-B

asked by: Dustan H

0

Expert Reply:

Hey Dustan,

The Round A-Frame Trailer Jack # TJA-2000S-B does not include mounting bolts or nuts, so you'll need to purchase those separately.

You'll need three 3/8"-16 Grade 5 bolts, along with matching nuts and washers if your trailer's mounting plate doesn't already have threaded holes. These are readily available at most local hardware stores.

Are you replacing an existing A-frame jack or installing one for the first time? You can likely just reuse the hardware if you're replacing a jack.

expert reply by: Andrew N

0

Answer 1

Hey Craig. Had to go measure this myself out in our warehouse, I see we don't have this listed. That opening is large enough for a 1" thick panel. What are you looking to panel?

view full answer...

Answer 2

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 3

Hi Collin, welcome back! The most economical replacement is going to be from Advent Air. You will need a complete system since everything moved to R32 refrigerant. If your upgraded thermostat is R32 compatible, or a smart thermostat that got a…

view full answer...

Answer 4

The KH97202 caliper you have pictured can actually be the left (driver) side or the right (passenger) side. So it wasn't necessarily installed backwards and I found a couple pictures showing that they used to put that casting number on both…

view full answer...

Answer 5

Hey Steve, hope you are well! Unfortunately, we do not offer a replacement rod, screw and nut for the #TJA-2000S-B jack. We have replacement gears, but the rod and nut are not available as a replacement part. I wish we did because then I could go…

view full answer...

Answer 6

It sure is Steve and welcome back! The etrailer Sidewind Trailer Jack w/ Drill Adapter item #e88GV is the correct jack if you don't want the SnapPad. This one is designed to fit the standard bolt pattern of an A-Frame trailer coupler and can be…

view full answer...

Answer 7

Hello Chris, Thanks so much for writing in and a double thank you for including the full brake assembly part number. That is incredibly helpful! Since you have the Kodiak Disc Brake Kit 11.35" Rotor #120 Spindle 12K ALKO #K2HR12A11-120DW, you…

view full answer...

Answer 8

Hey Dustan, The Round A-Frame Trailer Jack #TJA-2000S-B does not include mounting bolts or nuts, so you'll need to purchase those separately. You'll need three 3/8"-16 Grade 5 bolts, along with matching nuts and washers if your…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hello Ben, Thanks for writing in! Yes! The WeatherTech Front Auto Floor Mats #WT54TZ you were looking at are made specifically for the factory vinyl floor in your 2026 Ram 2500. For the rear, WeatherTech does not have a matching custom-fit rear mat…

view full answer...

Answer 11

Hey Roy, that is quite the truck! Since it is a dump truck you will want the higher capacity from the Timbren Suspension Enhancement System #TFRSDE. This gives you up to 12,000 lbs of additional support to handle those heavy loads and reduce that…

view full answer...

Does etrailer Round A Frame Trailer Jack Come With Mounting Hardware?

Product Page this Question was Asked From

Continue Researching