Are RVPaws Stronger Than OEM Jack Pads On RV With Bent Factory Jack Feet?

Question

Question:

I bent one of the factory jack feet on my RV. Are these RVpaws pads a stronger replacement?

asked by: Mark

0

Expert Reply:

Good question, Mark. The RVpaws V2 pads are definitely stronger than most OEM setups. They are built from 1/4" plate steel with 6 gussets, so they’re a nice upgrade over thinner factory-style feet that have about 1/8" thick plate.

The right part depends on your leveling system: # RV24FR fits standard 2" square jack legs, # RV57FR fits standard 2" round jack legs, # RV34FR fits Lippert Level Up and Lippert Titan systems, and # RV84FR fits Equalizer systems with 12" round feet. If you can tell me what leveling system you have or whether the jack leg is round or square, I can help narrow it down.

expert reply by: Andrew N

0

Mark

6/16/2026

I have the Ultra Fab setup.

Andrew N.

6/16/2026

@Mark Oh okay nice, so that should use the standard 2" square tube. I do recommend confirming. If that checks out, you can use the # RV24FR which fits 2" square tubes. Make sure you're measuring the bottom part where the foot attaches, not the upper outer tube which is larger diameter.

Answer 1

Good question, Dave. The easiest way is to match the RVpaws kit to your jack leg or leveling system. For example, there are specific kits for the brands and lineups out there: Standard 2" round jack leg = #RV57FR Standard 2" square jack leg…

view full answer...

Answer 2

Hey Dennis! If your fifth wheel uses standard 2" square leveling jack legs, the RVpaws articulating jack pads #RV24FR is the correct kit. If the legs are standard 2" round instead, you’d use #RV57FR. If you actually have Lippert Titan or…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Good question, Mark. The RVpaws V2 pads are definitely stronger than most OEM setups. They are built from 1/4" plate steel with 6 gussets, so they’re a nice upgrade over thinner factory-style feet that have about 1/8" thick plate. The right…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Are RVPaws Stronger Than OEM Jack Pads On RV With Bent Factory Jack Feet?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching